Autostacker™ Parking Lift
26
P/N 5900002 — Rev. D — August 2019
The following procedure includes instructions for anchoring the Console into place. If you prefer, you
can defer anchoring the Console into place for later. Simply return to this section when you want to
anchor the Console into place.
To assemble the Console and attach the Power Unit
:
1.
Select a site for the Console that permits operators to have a full, unobstructed view of the Lift.
If you are going to use the included Hydraulic Hoses, the Console needs to be near the front of the
Autostacker; it can go on either side, up to 30 inches away.
2.
Arrange all of the Console components near where you are going to assemble it.
3.
Lay the Back Plate flat on the ground, with the Mounting Bracket for the Power Unit facing up.
4.
Put the Grommets into place in the Grommet Holes on the bottom of the Left and Right sides.
5.
Put the Left Side on the left and the Right Side on the right, then attach both of them to the Back.
Note that the Flanges on the bottoms of both sides need to be on the inside and the Back
attaches on the outside of the two sides.
Do not attach the Nuts at the top of the sides or the Back at this point;
these will be
attached later when you are ready to attach to the Top of the Console.
6.
Remove the Power Unit from its packing material.
7.
Stand up the Console, then using the supplied Nuts and Bolts, attach the Power Unit to the Power
Unit Plate.
8.
Attach the Power Disconnect Switch; one piece goes on the inside of the Right Side, the clear
piece goes on the outside of the Right Side; use four screws to connect the clear piece on the
outside to the inside piece, then add the red/yellow switch on the outside using a single screw.
Important
: All of the components of the Console are now in place, but they are not all
connected. To connect the Hydraulic Hoses, Return Lines, and the other
connections to the Power Unit, you are going to need to remove both the Top of
the Console and the Front. See
9.
If you are ready to anchor the Console in place, find the four holes in the bottom of the Console
base (on the inside) and mark the locations; the four Anchor Bolts go in those holes.
10.
Move the Console out of the way.
It is much easier to drill the holes for the Anchor Bolts if the Console is out of the way.
11.
Drill four holes 3/8" wide by 2.5" deep in the concrete floor at the locations you just marked.
Go in straight; do not let the drill wobble. Use a carbide bit (conforming to the current ANSI
B212.15).
12.
Remove all dust from the Holes.
Use a wire brush, vacuum, hand pump, or compressed air. Do
not
ream the Hole. Do
not
make
the hole any wider than the drill bit made it.
13.
Move the Console over the four holes.
14.
Insert an Anchor Bolt with Washer into each hole, then tap it down into the hole.
15.
Wrench the Anchor Bolt
clockwise
to the recommended installation torque, 85-95 pound feet,
using a Torque Wrench.
Содержание Autostacker PL-6SR
