BendPak Autostacker PL-6SR Скачать руководство пользователя страница 59

Страница: 59 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

Attach the Conduit Tube

In order to place the Control Stand at the

Rear

of the Lift, you need to first attach the Conduit Tube to

the Bottom Connector Tube.
If you plan to position the Control Stand at the Front of the Lift, continue to the next section.
As mentioned in

Positioning the Bottom Connector Tube

, there is a Window on the Bottom

Connector Tube used for routing the Control Stand wiring. The Conduit Tube protects the Control

Stand wiring from being exposed and damaged.
The components involved include:
•

Conduit Cover Plate

. Attaches to the Window on the Bottom Connector Tube, facing the Rear

of the Lift.

•

Solid Cover Plate

. Attaches to the Window on the Bottom Connector Tube, facing the Front of

the Lift.

•

Conduit Fitting

. Attaches to the Conduit Cover Plate and holds one side of the Conduit Tube.

•

Conduit Tube

. Attaches to the Conduit Fitting. Used for routed the Control Stand wiring.

The following drawing shows how to attach the Conduit Tube to the Bottom Connector Tube.

Not to scale. Not all components are shown. Side view.

To attach the Conduit Tube

Find the Conduit Cover Plate, Solid Cover Plate, and the Conduit Fitting.

Attach the Conduit Fitting to the Conduit Cover Plate, then attach the Conduit Cover Plate to the

Window on the Bottom Connector Tube.
Use two M6 x 1 x 10 Screws.

Attach the Solid Cover Plate to the Window on the Connector Tube facing to the front of the Lift.
Use two more M6 x 1 x 10 Screws.

Connect the Conduit Tube to the Conduit Fitting, then adjust the screw on the Fitting to hold the
Tube securely in place.

Содержание Autostacker PL-6SR








































































































Результаты поиска

Содержание Autostacker PL-6SR

Отзывы:

BendPak Autostacker PL-6SR, Инструкция по установке и эксплуатации, Страница: 59 / 104

Результаты поиска

Содержание Autostacker PL-6SR

Отзывы: