BendPak Autostacker PL-6SR Скачать руководство пользователя | Manualshive

Страница: 36 / 104

background image

Autostacker™ Parking Lift

36

P/N 5900002 — Rev. D — August 2019

Test the Autostacker

Before putting your Autostacker into normal operation, we recommend breaking it in by raising and

lowering it a few times. This will help you get a feel for how to operate it and also helps to get any
residual air out of the hydraulic system.

Tip

Residual air in the hydraulic system can cause the Autostacker to shake, move
erratically, or squeak; this is normal. If it happens to you, do not worry; it will go

away quickly as the Autostacker is self-bleeding.

Neither the Platform nor the Drive-On Ramp need to be installed to test the lift. You also do not need

weight on the Lift.

Note

: The Autostacker lowers a little slower with no weight on it.

To test your Autostacker

:

1.

Check the area around and above the Autostacker for obstructions.
Move them if you find any.

2.

Insert the key and move it to the On position.

3.

Press and hold

Up

.

The Autostacker starts rising.

4.

Before reaching the first Safety Lock, release

Up

.

The Autostacker stops rising.

5.

Press and hold

Down

.

The Autostacker starts lowering.

6.

When the Autostacker gets to the ground, it stops lowering; release

Down

.

7.

Wait for one minute.

⚠

WARNING

The Autostacker’s Power Unit is not a constant duty motor; it cannot be run
continuously.

8.

Repeat the process, this time raising the Autostacker just past the first Safety Lock.
You can tell when the Autostacker passes a Safety Lock: when the Lock Hood goes past a Lock
Block, it hits the base and makes an audible click. Refer to

About Safety Locks

for more

information.

9.

If the Autostacker is working without shaking, moving erratically, or squeaking, there is no need to

repeat the procedure.
If the Autostacker is shaking, moving erratically, or squeaking, repeat the procedure one more
time, raising the Autostacker to the second Safety Lock.
It is normal for the Autostacker to shake, move erratically, or squeak when you first get it. Using it a

few times almost always fixes those issues.
If your Autostacker continues to have problems well past the break-in period, refer to

Troubleshooting

for additional information.

«
...
34
35
36
37
38
...
»

Содержание Autostacker PL-6SR









































































































Отзывы:

Нет отзывов

Похожие инструкции для Autostacker PL-6SR

Бренд: kaarta Страницы: 29

Бренд: RAM Страницы: 616

Бренд: Nav TV Страницы: 9

Бренд: Honda Страницы: 81

Бренд: ULTIMATE SPEED Страницы: 50

Бренд: Mercedes-Benz Страницы: 39

Бренд: Kurzweil Страницы: 374

Бренд: THIEYE Страницы: 88

Бренд: Honda Страницы: 124

PRIME DESIGN HXR-269-E-UM3-80

Бренд: Safe Fleet Страницы: 12

Бренд: iDataLink Страницы: 6

Бренд: Calix group Страницы: 4

Бренд: TATA Motors Страницы: 151

QUICKDRAW RACHET TIE-DOWNS 855

Бренд: Thule Страницы: 3

Бренд: Jaeger Страницы: 14

Бренд: TracRac Страницы: 8

Бренд: Renault Страницы: 11

Бренд: Westin Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды