BendPak Autostacker PL-6SR, Инструкция по установке и эксплуатации

Страница: 8 / 104

Autostacker™ Parking Lift
8
P/N 5900002 — Rev. D — August 2019
Components
Autostacker components include:
•
Console . Hosts the Controls for your Autostacker and the Power Unit. The Console is designed
to go on either side of the front of the Autostacker. The included Hydraulic Hoses let you put the
Console up to 30 inches away from the Autostacker. For a Single-Lift setup.
• Platform . Angled metallic deck that holds Vehicles. The Platform has the Tire Trough at one end
(the front) and the Drive-Up Ramp at the other end (the back).
• Drive-Up Ramp . Gives you access to the Platform. Note that the Tires of the Vehicle you are
parking on the Platform can be placed on the Drive-Up Ramp.
• Tire Trough . Lowered section of the Platform that holds the Vehicle’s tires. The Tire Trough
functions as tire chocks, so it is very important that the wheels of the Vehicle sit fully in the Tire
Trough.
• Patented Door-sentry™ car door protectors . Protects the car doors of the Vehicle parked
under the Platform. You should carefully open the car doors of the Vehicle parked under the
Platform, but the car-door protectors are there in case of contact.
• Leg Assemblies . The Autostacker comes partially assembled, making installation easier and
faster. There are two Leg Assemblies, left and right. Each Leg Assembly has a Platform Arm, Leg,
Cylinder, and Base. Note that the two Leg Assemblies are heavy and can damage materials like
tile, sandstone, and brick if not handled correctly; you must use a lifting device like a Forklift or
Shop Crane to move the Leg Assemblies.
• Left and Right Legs . Part of a Leg Assembly, they raise and lower the Platform.
• Safety Locks . Hold the Platform in place while it is raised. Multiple Safety Locks let you select
the right Platform height for your needs.
Only leave your Autostacker on the ground or
on the Safety Locks.
• Top Safety Lock . Provides the most space for the Vehicle under the Platform. The heights of all
six Safety Locks are listed in Raising a Vehicle .
• Lowest Safety Lock . Provides the most space for the Vehicle on the Platform.
• Left and right Cylinders . Also part of a Leg Assembly, they move the Legs up and down using
hydraulic power. The Cylinders are synchronized so that raising and lowering the Platform is even,
smooth, and rapid.
• Top and Bottom Connector Tubes . Located at the front of the Lift, the Connector Tubes
hold the Autostacker superstructure together. The Bottom Connector Tube is hollow; the Hydraulic
Hoses and the Return Lines are routed to the Console through the Bottom Connector Tube.
• Hydraulic Hoses . The Hydraulic Hoses provide hydraulic power to the Hydraulic Cylinders,
which they use to raise and lower the Lift.
• Return Line . Returns extra Hydraulic Fluid to the reservoir on the Power Unit. Connect to the top
of the Hydraulic Cylinders.
• Velocity Fuse . Prevents the Hydraulic System from failing in the event of a sudden, catastrophic
loss of Hydraulic Fluid pressure; if a Hydraulic Hose were accidentally cut, for example, while the
Platform was raised with a Vehicle on it.
• Rubber Padding . Offers padded protection if you accidentally bump your head into the Platform
Arm when passing underneath the Platform. One per Leg Assembly.
• Conduit Tube . Not shown . Used for routing electrical wiring if you have a Control Stand at the
Rear of the Lift. For a Multi-Autostacker setup; see Multi-Autostacker for additional information.
• Control Stand . Not shown . Holds the Controls to operate a specific Lift in a Multi-Lift setup, and
can be placed at the Front or Rear of the Lift. See Multi-Autostacker for additional information.
• Safety Placard . Not shown . Includes safety and operation instructions; attaches to the Control
Stand. See Multi-Autostacker additional information.