BendPak Autostacker PL-6SR Скачать руководство пользователя | Manualshive

Страница: 51 / 104

background image

Autostacker™ Parking Lift

51

P/N 5900002 — Rev. D — August 2019

Multi-Autostacker

Autostacker is available in a Multi-Lift configuration where you can control up to 12 Lifts with one
Master Power Unit; however, only

one

Lift can be raised or lowered at a time.

The installation for each Autostacker in a Multi-Lift setup is similar to that of a single Autostacker. The
main differences include separate procedures for routing the Hydraulic Hoses and the Return Line to a

Master Power Unit, in addition to installing a Control Stand for each Lift that allows you to operate a

specific Autostacker in your setup. The following pages describe those procedures.
For a Multi-Lift setup, you will need the following:
•

Autostacker Lifts

. You decide how many Lifts you want in your setup.

•

Control Kits

. Connects the Control Stand and Hydraulic Hoses to the Lift. One Kit per Lift.

•

MPU

(Master Power Unit). Provides the Hydraulic force needed to operate the Lifts. One MPU for

up to 12 Lifts.

•

MPU

Plumbing Kit

. Connects the Master Power Unit to the first Lift. One Kit total.

•

MPU Enclosure

.

Optional

. Protects the Power Unit from the outdoor elements. Not included.

The following drawing shows the Control Stands at the Front of the Lifts.

Not necessarily to scale. Not all components are shown. The Front of the Lift is where the Front of the
Vehicle commonly faces once driven onto the Platform

.

«
...
49
50
51
52
53
...
»

Содержание Autostacker PL-6SR









































































































Отзывы:

Нет отзывов

Похожие инструкции для Autostacker PL-6SR

Electronic Parking Disc II

Бренд: Jacob Jensen Страницы: 28

GRAND CHEROKEE 2023

Бренд: Jeep Страницы: 108

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 44

CLAVINOVA CVP-501

Бренд: Yamaha Страницы: 138

Clavinova CVP-403

Бренд: Yamaha Страницы: 4

Бренд: Romik Страницы: 6

10-8002-C11670C

Бренд: Saleen Страницы: 17

Бренд: Mazda Страницы: 13

VIEWLINE 52 MM - MOUNTING 11-09

Бренд: VDO Страницы: 4

Бренд: BMW Страницы: 38

Бренд: Meta System Страницы: 16

Бренд: Subaru Страницы: 540

Бренд: Acura Страницы: 7

Бренд: BraunAbility Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды