BendPak Autostacker PL-6SR Скачать руководство пользователя | Manualshive

Страница: 60 / 104

background image

Autostacker™ Parking Lift

60

P/N 5900002 — Rev. D — August 2019

Installing the Control Stands

The Control Stand holds the Controls to operate a Lift in your setup; each Lift has its own Control

Stand. The Control Stand can be placed at the Front

or

Rear of the Lift, although the installation for

either orientation is different. Those procedures are described here.
Each Control Stand comes with a Placard containing operation instructions.
The following steps explain how to

install

, but not make the connections to, the Controls for each

Lift. An Electrician is

not

needed to install the Controls, only to connect them to the Power Unit.

⚠

DANGER

Do not connect the wires to the Power Unit at this point; that task is for an
Electrician. All wiring connections made to the Power Unit must be performed by a

licensed, certified Electrician.

The following drawing shows the Control Stand at the

Front

of the Lift.

Not necessarily to scale. Not all components shown. Drawing shows the Stand at the Front of the Lift.

To install the Control Stand at the

Front

of the Lift

:

1.

Find the Control Box, Control Stand, and the three rolls of Electrical Cables from the Control Kit (14

AWG-4, 16 AWG-2, and 16 AWG-6).

2.

By the Power Unit, route the 14-4 Cable through the Bottom Connector Tube.
Let the wires hang out of the Window you want to use.

3.

Place the Control Stand nearby the selected Window, with the opening at the bottom of the
Control Stand facing towards the Lift.

4.

Remove the Screws from the Control Box to have access to the wiring inside.

5.

Connect the 16-6 Cable to the Controls, then route the Cable through the Stand.
Refer to

Wiring Diagrams

for wiring information.

6.

Connect the two Solenoids on each Lift together with the 16-2 Cable, then attach the 16-2 cable
to the 16-6 Cable.
Refer to

Wiring Diagrams

for wiring information.

«
...
58
59
60
61
62
...
»

Содержание Autostacker PL-6SR









































































































Отзывы:

Нет отзывов

Похожие инструкции для Autostacker PL-6SR

Бренд: 4iiii Страницы: 19

Бренд: EAL Страницы: 4

Бренд: Zavoli Страницы: 26

Бренд: Radio Shack Страницы: 46

Бренд: Generalmusic Страницы: 24

2005 Sierra Denali

Бренд: GMC Страницы: 428

Бренд: Mercedes-Benz Страницы: 346

Бренд: Thule Страницы: 4

Бренд: Whispbar Страницы: 15

Бренд: Ford Страницы: 22

Бренд: Subaru Страницы: 99

01 29 9 416 497

Бренд: BMW Страницы: 5

Transit Vancouver Wagon

Бренд: Webasto Страницы: 44

Бренд: Cadillac Страницы: 522

Бренд: Sears Страницы: 41

Impala Limited 2014

Бренд: Chevrolet Страницы: 356

Electra 225 1965

Бренд: Buick Страницы: 914

Бренд: Beper Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды