BendPak Autostacker PL-6SR Скачать руководство пользователя

Страница: 71 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

Multi-Autostacker

Each Control Stand requires three Electrical Cables, of varying gauges:
•

#14 AWG

. Four wires;

Green

Red

Black

, and

White

. One end of the Cable goes to the Power

Unit, and the other end goes through the Bottom Connector Tube, connecting to each Lift.

•

#16 AWG

. Two wires;

Black

and

Blue

. Interlinks the two Solenoids on each Lift, and connects to

the Blue and Orange wire coming from the Control Stand.

•

#16 AWG

. Six wires;

Green

Red

Black

White

Blue

, and

Orange

. One end connects to the

Control Box (on Control Stand), and the other end connects to the Cable that is routed through the

Bottom Connector Tube.

The following graphic shows the various connections to make to your Electrical system.

Not drawn to scale. Some components are missing or exaggerated for easier understanding

Содержание Autostacker PL-6SR








































































































Результаты поиска

Содержание Autostacker PL-6SR

Отзывы:

Похожие инструкции для Autostacker PL-6SR

Бренды по названию

Популярные бренды

BendPak Autostacker PL-6SR, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Autostacker PL-6SR

Отзывы:

Похожие инструкции для Autostacker PL-6SR

Бренды по названию

Популярные бренды