BendPak Autostacker PL-6SR Скачать руководство пользователя

Страница: 53 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

Positioning the Bottom Connector Tube

If you want to position the Control Stand at the

Rear

end of Lift (the Drive-up end), make sure the

Window for routing the Control Stand wires through the Bottom Connector Tube is on the same side

of the Lift where the Control Stand will go.
If you want to place the Control Stand at the

Front

of the Lift, continue to the next section.

The Window for the Control Stand wiring can go on either side of the Lift, as long as the small gap on

the Bottom Connector Tube (from the top Bolts to the top of the Tube) remains at the top and the

large gap (from the bottom Bolts to the bottom of the Tube) is at the bottom, as shown below.
The Power Unit must also be near the Front of the first Lift (the Lift closest to the Power Unit); it can go

on either side of your setup, up to 30 inches away.
The following drawing shows the general arrangement for the Bottom Connector Tube.

Содержание Autostacker PL-6SR








































































































Результаты поиска

Содержание Autostacker PL-6SR

Отзывы:

Похожие инструкции для Autostacker PL-6SR

Бренды по названию

Популярные бренды

BendPak Autostacker PL-6SR, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Autostacker PL-6SR

Отзывы:

Похожие инструкции для Autostacker PL-6SR

Бренды по названию

Популярные бренды