BendPak Autostacker PL-6SR Скачать руководство пользователя

Страница: 47 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

Maintenance

⚠

DANGER:

Before performing any maintenance on your Autostacker, make sure it is

completely disconnected from power

. If your organization uses

Lockout/Tagout policies, make sure to implement them after connecting to a power
source.

To maintain your Autostacker

•

Daily

: Keep the Autostacker clean. Wipe up any spills, clean any dirt.

•

Daily

: Make a visual inspection of all moving parts and check for damage or excessive wear.

Replace any damaged or worn parts before using the Lift.

•

Daily

: Make sure Safety Locks are in good working condition. Do not use your Autostacker if the

Safety Locks are damaged or excessively worn.

•

Twice a Week

: Sweep the Bases, removing all debris. Pay special attention to the Safety Locks

and the wheel tracks; if these areas are dirty, the Lift may not work normally.

•

Weekly

: After cleaning the wheel tracks, apply a lubricant (WD-40®, for example) to the wheel

tracks to help them roll easily. The wheels are self-lubricating.

•

Weekly

: Check all controls, including emergency stop, to make sure they are functioning

normally.

•

Weekly

: Check all labels on the Autostacker. Replace them if they are illegible or missing.

•

Every Two Weeks

: Lubricate the grease fittings on the Lift. There are four Grease Fittings on

each side of the Autostacker: one where the bottom of the Cylinder meets the Base, one where
the top of the Cylinder meets the Leg, one on the underside where the two Legs cross, and one

where the Leg meets the Top Connector Tube. We recommend using white lithium grease or

similar.

•

Monthly

: Check the Hydraulic Fluid levels. Refill if low.

•

Every two months

: Check all Bolts to make sure they are tight. If not, tighten them.

•

Every three months

: Damp wash all exposed surfaces to protect against corrosive debris.

•

Every six months

. Check the electrical wiring for loose connections; if you find any, secure

them.

⚠

WARNING:

Do not operate your Autostacker if you find issues; instead, take it out of service,

then contact your Autostacker dealer, visit

autostacker.com/support

, email

[email protected]

, or call

(888) 977-8225

Содержание Autostacker PL-6SR








































































































Результаты поиска

Содержание Autostacker PL-6SR

Отзывы:

Похожие инструкции для Autostacker PL-6SR

Бренды по названию

Популярные бренды

BendPak Autostacker PL-6SR, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Autostacker PL-6SR

Отзывы:

Похожие инструкции для Autostacker PL-6SR

Бренды по названию

Популярные бренды