BendPak Autostacker PL-6SR Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 104

background image

Autostacker™ Parking Lift

66

P/N 5900002 — Rev. D — August 2019

⚠

DANGER

All wiring

must

be performed only by a licensed, certified Electrician. Do not

perform any maintenance or installation on the Lift without first making sure that

main electrical power has been disconnected from the Lift and cannot be re-
energized until all procedures are complete. If your organization has

Lockout/Tagout policies, implement them after connecting to a power source.

To connect to a power source

:

1.

Have a certified, licensed Electrician connect an appropriate plug to the wiring, coming out of the

Power Unit.
The plug is

not

supplied with the Power Unit.

2.

Connect the power source cable to the plug you just connected.
The power source cable is

not

supplied with the Power Unit.

Refer to

Wiring Diagrams

for wiring information.

3.

Connect the Control Stands to the Power Unit.
Refer to

Wiring Diagrams

for wiring information.

4.

Connect the Power Disconnect Switch.
Refer to

Wiring Diagrams

for wiring information.

5.

Have a certified, licensed Electrician check for any loose connections.

6.

Fill the Hydraulic Fluid Reservoir.
The Power Unit’s Hydraulic Fluid reservoir must be filled with Hydraulic Fluid or Automatic

Transmission Fluid before you begin operation. When you receive it, the reservoir is empty; the

Power Unit will not work correctly until there is an adequate supply of the approved fluids.
Approved fluids are any general purpose ISO-32, ISO-46, or ISO-68 hydraulic oil or approved

automatic transmission fluids such as Dexron III, Dexron VI, Mercon V, Mercon LV, or any synthetic

multi-vehicle automatic transmission fluid.

⚠

WARNING

Do not run the Power Unit without Hydraulic Fluid; you will damage it. Keep the
Power Unit dry; damage the Power Unit caused by water, detergents, acids, and

other liquids is not covered by the warranty.

«
...
64
65
66
67
68
...
»

Содержание Autostacker PL-6SR









































































































Отзывы:

Нет отзывов

Похожие инструкции для Autostacker PL-6SR

Бренд: Casio Страницы: 22

Бренд: Barker Страницы: 2

Бренд: TATA Motors Страницы: 156

Бренд: JANE Страницы: 58

STO N SHO SNS 144

Бренд: Big Mikes Performance Parts Страницы: 7

Бренд: Lincoln Страницы: 10

Бренд: mtf TRANSPORT SYSTEM Страницы: 9

Бренд: Toyota Страницы: 600

Бренд: KEKO Страницы: 3

Бренд: Movon Страницы: 43

Бренд: INDIWORK Страницы: 18

Бренд: Opel Страницы: 103

Бренд: Enduro Страницы: 52

Бренд: Lincoln Страницы: 586

Бренд: Axxess Страницы: 16

Бренд: Whispbar Страницы: 14

Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600

Бренд: Ecco Страницы: 2

Бренд: Mercedes-Benz Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды