Beijing Dahao Technology BECS-D56 страница 8 Скачать руководство пользователя

Страница: 8 / 188

Chapter 1 General Descriptions

Compulsory

Overloading may cause serious loss. Please load according to the

instruction on the box..

Installation

Caution

Don't jam the vent on the device. Don’t plug up the machine, or it may

cause fire or electronic shock.

Caution

Make sure the installation direction is correct..

Caution

Don't expose the machine to humidity gas, poisonous gas, water, and dust.

Cable Connection

Forbidden

Don't test the insulation of the circuit loop.

Forbidden

Never try to connect overloading electronic device on the connector or the

power socket.

Caution

Make sure the insulation cover of each cable is fine.

Caution

Communication cable and power cable should be separated.

Caution

All the cables should be well fixed. Don’t put any strength on cables. Make

sure the turning point of cable is well protected. Add pipes to increase

insulating capability.

Caution

Machine should be grounded. The resistance should be no larger than 10

Operating Direction

Danger

Don't operate the machine when there is any damage on the protection

shell.

Forbidden

When machine is running, do not touch any running part.

Caution

Make sure the configuration of power supply in normal. Use stabilized

voltage power supply when the voltage rebound is between -10%~10%.

Caution

In case of warning, please check out the problem. Operation can only be

carried out again when problem is solved.

Caution

The power supply has over-currency protection function. There is a 3 mins

time lag before the function can be used again.

2 BECS- D56 computerized embroidery machine owner’s manual

Содержание BECS-D56





























































































































































































Результаты поиска

Содержание BECS-D56

Отзывы:

Похожие инструкции для BECS-D56

Бренды по названию

Популярные бренды

Beijing Dahao Technology BECS-D56, Руководство пользователя

Результаты поиска

Содержание BECS-D56

Отзывы:

Похожие инструкции для BECS-D56

Бренды по названию

Популярные бренды