Beijing Dahao Technology BECS-D56 страница 132 Скачать руководство пользователя

Страница: 132 / 188

Chapter 11

Directions on Coiling, Taping and Zigzag Embroidery

D44 M Axis Work OFF Angle: 0, 90

In normal and sequin embroidery, if this parameter is set at 0, the M axis will stop at the

horizontal position; if it is set at 90, the M axis will stop at the vertical position. When the

distance between the normal embroidery head and special embroidery head is small, this

parameter must be set as 90° to avoid crashing.

D39 Z Shift Control Angle: 0~180

When the rotating angle is larger than the set value, the Z axis will wing faster.

D41 Adj Zig Rod Angle: 1~3

It is the starting angle of the rod, which indicates the relative position of the needle bar and

thread. It is used for adjusting the embroidery quality. “1” means the swing starts at an early

angle; “2” means the swing postpones certain angle; “3” indicates the swing postpones certain

angle again and starts.

10.

C36 Ratio of Coil Emb. (The ratio of coiling) : “1~4 Sti/L”

The parameter can change the coiling density; e.g. the set value 2 means one coiling every two

stitches.

11-4

Relative Operations of Special Embroidery

11.4.1

Shift between Flat Stitch Head and Special Head

Manual Shift

In the main screen, press the key

“ ”

to enter color changing screen.

Move cursor to the figure corresponding to the special embroidery method and press “

”to

save the selected method. Press “

”to exit.

126 BECS- D56 computerized embroidery machine owner’s manual

Содержание BECS-D56





























































































































































































Результаты поиска

Содержание BECS-D56

Отзывы:

Похожие инструкции для BECS-D56

Бренды по названию

Популярные бренды

Beijing Dahao Technology BECS-D56, Руководство пользователя

Результаты поиска

Содержание BECS-D56

Отзывы:

Похожие инструкции для BECS-D56

Бренды по названию

Популярные бренды