Barudan BEXT 120V Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 284

background image

１‐３

！

Danger

◆

An embroidery machine should never be left unattended when plugged in.

◆

Always power off and unplug this embroidery machine from the electric outlet immediately
before cleaning.

◆

Always turn off the Automat and the Driver Box when not in use for long periods of time.

！

Warning

◆

Do not allow to be used as a toy. Close attention is necessary when this embroidery machine is

used by, or near children.

◆

Use this embroidery machine only for its intended use as described in this manual.

◆

Use only attachments recommended by Barudan, as contained in this manual.

◆

Never operate this embroidery machine if it has a damaged cord or plug, if it is not working
properly, if it has been damaged or is wet. Contact Barudan America technical support.

◆

Never operate the embroidery machine with any air openings blocked. Keep ventilation

openings of the machine free from the accumulation of lint, dust, and loose cloth.

◆

Never drop or insert any object into any opening.

◆

Do not use outdoors.

◆

Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

◆

To disconnect, turn all controls to the off position, then remove the plug from the outlet.

◆

Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

◆

Keep fingers away from all moving parts. Special care is required around the sewing machine
needles.

◆

Always use the proper needle plate. The wrong plate can cause the needle to break.

◆

Do not use bent needles.

◆

Do not pull or push fabric while stitching. It may deflect the needle, causing it to break.

◆

Switch the sewing machine off when making any adjustments in the needle area, such as

threading the needle, changing a needle, replacing the bobbin, changing the presser foot, or
the like.

◆

Always unplug the machine from the electrical outlet when removing covers, lubricating or

when making any other user servicing adjustments mentioned in the instruction manual.

◆

Connect this embroidery machine to a properly grounded outlet only. See Grounding
Instructions.

◆

Always unplug before relamping. Replace bulb with same type rated Watts.

◆

Keep fingers away from moving parts, especially the area near trimmer blades.

◆

Keep Fingers away from disengaged sewing heads while operating.

Save these instructions

«
...
8
9
10
11
12
...
»

Содержание BEXT 120V





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BEXT 120V

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды