Bandit INTIMIDATOR 12XPC Скачать руководство пользователя

Страница: 21 / 153

Bandit

MODEL 12XPC

Before starting the machine, take a minute to

check a few things. The machine should be in an

area restricted from people passing by. This area

around the machine must be free of all objects that

can obstruct your movement when working with the

machine. The machine should be checked for loose

tools or foreign objects, especially in the infeed

hopper area. All tools not in use should be secured

in a tool box.

Operators

must

at all times be located within

easy reach of all feed control and shut‑off devices

when the unit is running. They must be attentive and

prepared to activate the devices.

Torn or loose clothing is more likely to get caught

in moving machinery parts or tree branches. Keep

such items as long hair, shirt sleeves, and shirt tails

properly contained. Avoid wearing necklaces, rings,

watches, and especially neckties while operating this

machinery. Make sure the machine is in excellent

condition, and all the guards are in place, tight and

secure.

Wear all personal protection equipment and follow

all safety standards per ANSI and OSHA instructions.

Examples of equipment: hard hat, face shield, safety

glasses, gloves, ear protection, etc. Do not wear

gauntlet or secured fi t gloves. Always keep a fully

charged fi re extinguisher with the machine while

operating or servicing the machine.

Striped refl ective tape has been installed on the

feed control handle of the machine. This tape is

refl ective, self adhesive and has contrasting colors.

The tape helps make the feed control handle stand

out more and it makes the rear of the machine

more visible to a vehicle behind the machine while

transporting. Striped tape can be obtained through

your local Bandit Dealer.

SAFETY PROCEDURES

CALIFORNIA

Proposition 65 Warning

Diesel engine exhaust and some of its

constituents are known to the State of

California to cause cancer, birth defects,

and other reproductive harm.

NOTICE

DANGER

WARNING

The words

Danger,

Warning,

Caution, and

Notice are used on the safety decals and throughout

this manual, to make you aware of the safety

procedures. These procedures are very important,

read and obey them.

YOUR SAFETY IS VERY IMPORTANT TO US!

This machine is equipped with safety decals,

guards and designs for your protection.

Don’t ever take the machine for granted, always be

cautious and careful when operating your equipment.

Read and follow all the instructions in your

manual thoroughly. Your safety is dependent on

your knowledge of how to operate and maintain this

machine. You may obtain additional copies of this

manual from your Bandit Dealer.

Before operating machine, you must have all

potential operators; read and understand manuals

and decals, watch the video and follow the

recommendations.

Regardless of how hard a manufacturer tries to

produce a safe machine, accidents still happen.

Normally accidents are caused by people making

mistakes. They do not read the manual, they ignore

warning decals or do not use lockouts provided for

their safety. This normally happens after the person

has become accustomed to the machinery. In the

initial start up and operation of the machinery, they

are cautious, they are very careful because they do

not understand the machine.

This equipment is intended for use by adults

who have been properly trained and are physically

capable of operating the machine safely. Never

allow minors to operate this machine. Never operate

any machine while under the infl uence of drugs or

alcohol. Never operate equipment that is in need of

repair or adjustment. Keep children, bystanders and

animals clear of working area.

There must be at least two qualified and

trained operators at the work site. They must be

positioned in safe working locations, following safety

procedures and instructions, and aware of each

others whereabouts. There must, also, be at least

two people on site during maintenance and service

procedures in case an accident should occur.

SAFETY PROCEDURES

Содержание INTIMIDATOR 12XPC


























































































































































Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 12XPC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды