Bandit INTIMIDATOR 12XPC Скачать руководство пользователя

Страница: 81 / 153

Bandit

MODEL 12XPC

Clearances that are too small will result in excessive drag and overheating while too much clearance

can render the brake nonfunctional.

For additional brake adjustment procedures consult the axle manufacturer manual.

RECOMMENDED BRAKE ADJUSTMENT PROCEDURE PER AXLE MANUFACTURER.

The proper clearance between the shoe and drum surfaces will be set up initially from our factory to assure

proper operation during the normal break in period. No further adjustment will be necessary until the vehicle

completes the recommended break in period of 200 miles (322 km).

Since all brakes of this type must be burnished or “run in” before their full eff ectiveness can be achieved, the

MFG. maintenance manuals call for readjustment after the fi rst 200 miles (322 km) of operation. This usually

allows ample time for the burnishing to take place. Readjustments are not necessary for brakes fi tted with

self-adjustment features although periodic inspection is suggested.

• Misalignment - from rough roads, pot

holes, excessive speeds and hitting curbs.

• Tire Width - the wider the tire for

fl otation, the more uneven the tire wear.

• Tire Air Pressure - to much or too little,

for the load.

• Vehicle Hitch Height - if trailer is

not level with ground, axle camber is

misaligned.

• Maintenance - wheel bearing

lubrication and adjustment. Follow axle

MFG. instructions.

• Brakes - uneven or misadjusted brakes

cause irregular brake activation.

MAINTENANCE

TIRE WEAR DIAGNOSTIC CHART

For additional parts break downs and service videos go to www.dexteraxle.com

Wear Pattern

Cause

Action

Edge

Wear

• Under

infl ation

• Adjust pressure to

particular load per

tire catalog

Side

Wear

• Not hauling

trailer level

• Bent axles

• Wide tires

• Wheel

bearings

• Must be hauled

parallel to the

ground

• Replace as

needed

• Characteristic of

wide fl otation tires

• Adjust or replace

Cup

Wear

• Out of

balance

wheel

bearings

• Check bearing

adjustment and

balance tires

• Adjust or replace

Center

Wear

• Over

infl ation

• Adjust pressure to

particular load per

tire catalog

Flat

Spots

• Wheel lock

up and tire

skidding

• Avoid sudden

stops and adjust

brakes

The wear pattern and tread life of tires

involves many variables that the user has

control of, but DOES NOT fall under faulty

manufacture or design.

The following is a list of some causes supplied

by tire suppliers and axle manufacturers:

AXLE SIZE

5200 LBS.

SIZE

12” x 2”

TYPE

Elec. or Hyd.

DIAMETRAL CLEARANCE

.040” (1 mm)

CLICKS TO BACK OFF

10 TO 16

NOTICE

The following shows the correct adjustment for the MFG. brakes of 12” diameter.

Содержание INTIMIDATOR 12XPC


























































































































































Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 12XPC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды