Bandit INTIMIDATOR 12XPC Скачать руководство пользователя страница 28

Страница: 28 / 153

Bandit

MODEL 12XPC

Do not attempt to operate the machine on an ascending or descending slope of more than 25° or 46% or

a side slope of more than 17° or 30%, it is Dangerous and could be Fatal. This is the maximum slope grade

the machine can be operated on if the hydraulic system, self propelled undercarriage, and engine are running

at maximum performance and good traction is sustained.

The machine should never be parked on a slope at any time. The machine can coast or creep causing

equipment and/or personal injury.

Make sure everyone is clear of machine before moving the machine. Stay clear of undercarriage travel

system when the machine is moving.

DO NOT entangle feet or hands in undercarriage travel system.

NEVER sit, stand, lay, climb or ride anywhere on this machine while it is running, operating, or in transit.

You will be injured.

Use

EXTREME CAUTION

when traveling over non-level surface! This machine can tip over or tip backwards

on non-level surface. You will cause engine damage, machine damage and possible personal injury!

Any increase from the specifi ed maximum operating angles may cause loss of lubrication function and

damage the engine.

IF MACHINE IS EQUIPPED WITH A SELF PROPELLED UNDERCARRIAGE

Machines equipped with undercarriage tracks are shipped with a manual from the track manufacturer.

Refer to it for service, operation, and safety information.

SAFETY PROCEDURES

DANGER

WARNING

25° MAX.

17° MAX.

Maximum Slope Grade

Diagram shows percentage to degree of slope.

Percentage is in vertical feet for every 100 horizontal feet.

Ascending or Descending Slope

Side Slope

100 FT. (30.5 m)

46 FT.

(14 m)

(46%)

30 FT.

(9.1 m)

(30%)

25° MAX.

17° MAX.

Содержание INTIMIDATOR 12XPC


























































































































































Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 12XPC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды