Bandit INTIMIDATOR 12XPC Скачать руководство пользователя

Страница: 34 / 153

Bandit

MODEL 12XPC

EXAMPLES:

Decals located on your Bandit equipment contain useful information to assist you in operating your equipment

safely. Some of the decals on your machine and their location are shown in this section.

It is very important that all decals remain in place and in good condition on your machine. Please follow

the care and instructions given below.

DECALS

1. You should use soap and water to keep your decals clean. Never use mineral spirits or any other

abrasive cleaners.

2. Immediately replace any missing or damaged decals. The location the decal is going to be applied

to must be clean and dry, and at least 40°F (5°C) before applying decal.

3. When the need arises to replace a machine component with a decal attached, be sure and replace

the decal.

4. Replacement decals are available, and can be purchased from the manufacturer or your Bandit Dealer.
5.

Peel back about half of the backer paper on the decal. Position it on the fl at, dry, clean surface so it

is smooth and secure. Peel off the remainder of the backer paper as you continue to stick the decal

on the surface.

6. Rub decal from the center outward to remove air bubbles and to secure contact.
7. Combination English / Spanish decals are typically standard. Other foreign language decals are

available and may be purchased. Mail translated decals required to Bandit Industries, Inc.

THE CLUTCH SHOULD

NOT

BE ENGAGED OR

DISENGAGED AT ENGINE SPEEDS ABOVE LOW

IDLE (ABOUT 1000 RPM’S).

DO NOT operate this Clutch/PTO unless proper adjustments and

lubrication are maintained per the Clutch/PTO Manufacturer’s Manual.

Diff erent brands and models require diff erent service and operation

procedures. New Clutch/PTO’s require more frequent adjustment.

GOOD OPERATORS

DON’T WASTE MONEY!

Clutches will fail, glaze over, and burn up from improper

adjustment. This will cost the owner of this machine

thousands of dollars to repair. A well maintained, correctly

adjusted clutch should function properly for years.

N-07 4/15

NOTICE

LEAVING THE CLUTCH DISENGAGED EVEN

FOR SHORT PERIODS OF TIME WILL

REDUCE PILOT BEARING AND CLUTCH

PLATE LIFE! REFER TO CLUTCH MANUAL FOR

OPERATING AND MAINTENANCE PROCEDURES.

Содержание INTIMIDATOR 12XPC


























































































































































Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 12XPC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды