Bandit INTIMIDATOR 12XPC Скачать руководство пользователя

Страница: 47 / 153

Bandit

MODEL 12XPC

This chipper hood engine disable plug is installed for safety purposes. It is designed to shut down the

engine if the hood pin is not properly in place holding the chipper hood in the closed position. The system

must be correctly maintained and operative at all times. If the disable plug is not correctly installed the engine

will not start or run.

The chipper hood engine disable plug is located on top of the chipper hood. The chipper hood engine

disable plug is made up of two parts: an electric socket and a disable plug. The electric socket is bolted to

the chipper hood engine disable plug mount bracket and the disable plug is attached by a cable to the hood

pin.

If the disable plug is not properly installed then the engine will not start or run. If the disable plug becomes

disconnected while the chipper engine is running the engine will be shut down or be disabled from running.

This is for safety purposes, to ensure that the hood pin is not removed and the chipper hood is not opened

while the engine is running.

The chipper hood engine disable plug is wired to shut down the chipper engine. When the disable plug is

pulled out of the electric socket the electric circuit is broken, disabling the engine.

The engine disable plug has a circuit fuse. If the engine will not start or run, check the fuse fi rst before

consulting the engine manufacturer’s manual. Circuit fuse locations: Caterpillar / Perkins - located at the

“BATT” wire near the ignition switch, Cummins - located by engine manufacturer near the starter (wires

labeled “POW”), John Deere - located by engine manufacturer “Short Stop” circuit breaker by the ignition

switch on the instrument panel or fuse by the ECM, and Deutz, Hatz, Honda, Kohler, and Robin - located at

the battery post on the starter.

CONTROLS

CHIPPER HOOD ENGINE DISABLE PLUG OPERATION

NOTICE

DISABLE PLUG

DRUM CHIPPER

DISC CHIPPER

ELECTRIC

SOCKET

PADLOCK

CABLE (TIGHT WHEN

PLUGGED IN AND

PADLOCK IS IN!)

HOOD PIN

ELECTRIC

SOCKET

PADLOCK

HOOD PIN

CHAIN

DISABLE PLUG

CHIPPER HOOD

HOOD DOOR

Содержание INTIMIDATOR 12XPC


























































































































































Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 12XPC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды