Bandit INTIMIDATOR 12XPC Скачать руководство пользователя страница 90

Страница: 90 / 153

Bandit

MODEL 12XPC

First put control bar in off position.

2. Disconnect hose coming out of the port farthest from the handle of the control valve from the optional

motor or cylinder, and plug the hose.

3. Leave all other hydraulic hoses connected.
4. Install pressure gauge in the valve port which had the hose of the optional motor or cylinder disconnected.
5.

Start engine with the control bar in the off position.

6. Adjust engine to full throttle.
7. Only operate the valve for that component to activate pressure gauge. Pressure gauge should read the

maximum specifi ed PSI (bar) for that component.

ONLY OPERATE VALVE FOR 4-5 SECONDS TO SET PRESSURE OR YOU MAY DAMAGE

HYDRAULICS.

Readjust relief pressure setting if needed, if not needed, shut off engine and remove plug and pressure

gauge. Reassemble control valve to optional motor or cylinder.

9. Check for hydraulic leaks.
10. Relief valve pressure should be checked and/or readjusted every month for best performance.

PROCEDURE FOR CHECKING OPTIONAL HYDRAULIC COMPONENTS

Before attempting any hydraulic pressure settings, make sure engine is shut off , engine key removed and in

your possession, hydraulic oil is clean, hydraulic tank is 3/4 to 7/8 full, and the machine has been pre-run to

warm the hydraulic oil. To correctly check relief valve pressure, gauge MUST be installed correctly.

WARNING

MAINTAIN HYDRAULIC PRESSURE AT SPECIFIED PSI (bar).

Yoke Lift

Cylinder

(OPTIONAL COMPONENT)

From

Pump

To Tank

Feedwheel

Control Valve

GAUGE

PLUG

YOKE LIFT CONTROL VALVE

ALL OPTIONAL COMPONENTS

MAY BE CHECKED THIS WAY

(VALVE FOR OPTIONAL

COMPONENT)

HYDRAULICS

Содержание INTIMIDATOR 12XPC


























































































































































Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 12XPC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды