Bandit INTIMIDATOR 12XPC Скачать руководство пользователя

Страница: 136 / 153

BANDIT CONTROLS

245774458290 21Dec2016

Notes

The tether is a back-up tool in case the radio fails. The tether has 2 (8) button keypads that communicate with

the main controller via CAN messages. The machine must be in Tether mode in order to activate the Tether.

Note: If Controller 1 (C1) loses communication with both the Display and the Radio receiver, C1 will default to

Tether mode internally.

There is a hardwired E-Stop switch to ground in the tether box. If the machine is in Tether mode and this

switch is open (or the tether cable broken), the system will E-Stop the engine.

(If Fuel Saver mode is turned on and the machine idles down due to light load conditions, simply press Throttle

Up and then press Feed Fwd to resume feeding).

(If the Winch Stow Switch indicates that the winch is out, Feed Fwd will stop automatically and the Tether

Winch functions will be enabled. The Tether Feed Fwd button then can be used to Feed Assist on Electric Feed

Assist machines. Once the Winch is properly stowed, Tether winch functions will be disabled and Feed Fwd

will operate as normal to resume chipping).

The Yoke/Lift is disabled while winch is deployed. Except, Yoke/Lift can momentarily operate with Feed-

Assist-Fwd. Yoke/Lift is fully enabled again once the winch is properly stowed tight on the stow bar.

When the mechanical control bar is in the reverse position a switch interrupts the FeedRev coils to prevent a

double reverse which would then feed forward.

Содержание INTIMIDATOR 12XPC


























































































































































Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 12XPC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды