Bandit INTIMIDATOR 12XPC Скачать руководство пользователя

Страница: 84 / 153

Bandit

MODEL 12XPC

Alternate hydraulic oils are available, but they do not equal the performance or longevity

of the “Hydrex XV” oil. Consult the following information supplied by the oil distributor.

HYDRAULICS

Some equipment and components such as a fl uid engagement clutch (PTO) have their own lubrication

requirements. Consult their manufactures manual for that information.

NOTICE

The above chart is a suggested guide for viscosity of hydraulic fl uids at start up ambient temperature.

The load, demand, and cleanliness of the equipment will aff ect actual oil temperatures which can

increase dramatically above ambient air temperatures during operation. The actual viscosity needed is

based on oil temperature during operation and not air temperature. Compare your fl uid specifi cations with

the specifi cations below to verify compliance.

When choosing a hydraulic fl uid ‑ these maximum and minimum specifi cations must be met

Minimum Viscosity during operation

= 12 cSt

Maximum No-Load Viscosity at start-up = 2000 cSt

Hydraulic fl uids vary in their resistance to oxidation at elevated temperatures, their ability to protect

against metal-to-metal contact under increasing temperature, and their ability to separate water from

the fl uid. Viscosity is temperature dependent. Fluids with high viscosity‑index (VI) will thin out slower

at higher temperature and thicken slower at colder temperatures allowing a wider operating range.

Choose a fl uid that has test results in these areas for best results.

Based on the varying temperatures of the area where Bandit equipment is used, and the high demand

and loads placed on this equipment, Bandit has fi lled each hydraulic system with Petro‑Canada’s Hydrex

XV All Season Hydraulic Fluid for maximum protection and performance.

Go to: lubricants.petro‑canada.com to fi nd a dealer near you.

NOTICE

CELSIUS (C)

-40 -34 -29 -23 -18 -12 -7 -1 +4 +10 +16 +21 +27 +32 +38 +43 +49 +54

FAHRENHEIT (F) -40 -30 -15 -10 0 +10 +20 +30 +40 +50 +60 +70 +80 +90 +100 +110 +120 +130

ANTI-WEAR HYD. OIL NO. 68

ANTI-WEAR HYD. OIL NO. 46

ANTI-WEAR HYD. OIL NO. 32

ANTI-WEAR HYD. OIL NO. 22

HIGH VI - ANTI-WEAR HYD. OIL NO. 46 (>140 VI)

PETRO CANADA HYDREX XV (245 VI)

HYDRAULICS

Содержание INTIMIDATOR 12XPC


























































































































































Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 12XPC, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 12XPC

Отзывы:

Похожие инструкции для INTIMIDATOR 12XPC

Бренды по названию

Популярные бренды