6 / 26
0006080844_201003
E
S
P
A
Ñ
O
L
CARACTERÍSTICAS TÉCNICO FUNCIONALES
• Funcionamiento en dos etapas progresivas de potencia.
• Posibilidad de funcionar con modulación de potencia mediante montaje en el
cuadro de mandos del regulador automático RWF40 (debe encargarse por
separado junto al kit de modulación específico).
• Posibilidad de obtener excelentes valores de combustión mediante la regulación
del aire comburente y del cabezal de combustión.
• Mantenimiento facilitado por la posibilidad de extraer el grupo de pulverización
sin desmontar el quemador de la caldera.
• Regulación del caudal mínimo y máximo del aire mediante servomotor eléctrico
con cierre de la válvula en parada para evitar dispersiones de calor a la chimenea.
• Bajo pedido se puede integrar el quemador con un precalentador complementario
del aceite combustible de funcionamiento a vapor que, en régimen, permite
calentar el combustible con el vapor de la caldera y obtener así un ahorro de
energía eléctrica.
• Provisto de 1 junta aislante para la fijación a la caldera, 2 tubos flexibles, 1 filtro
de línea autolimpiador con resistencia; la boquilla no está incluida, se debe
encargar por separado en función del caudal requerido.
• Bajo pedido: precalentador a vapor.
CARACTERÍSTICAS CONSTRUCTIVAS
El quemador está compuesto por:
• Toma de aire comburente con dispositivo para la regulación del caudal de aire.
• Brida de conexión al generador fija con bisagra para facilitar el desmontaje del
grupo pulverizador y del disco de la llama.
• Presostato del aire, que garantiza la presencia del aire comburente.
• Servomotor eléctrico con leva mecánica para la regulación simultánea del aire
comburente y del combustible.
• Resistencia calefactora para bomba, para válvula reguladora y para grupo
pulverizador.
• Grupo pulverizador con imán para el control de las agujas de envío/retorno
boquilla.
• Grupo de 2 precalentadores eléctricos del combustible en serie entre sí monta
-
dos en un bastidor que incluye válvula antigas, filtro autolimpiador, termómetro,
regulación electrónica de la temperatura y termostatos de seguridad.
• Rampa de gas de encendido del quemador provista de válvula de funcionamiento
y de seguridad, presostato de mínima, regulador de presión y filtro de gas.
• Aparato automático de mando y control del quemador según norma europea
EN230.
• Control de la presencia de llama mediante fotocélula UV.
• Instalación eléctrica con grado de protección IP40
.
Existen diferentes tipos de quemadores según el tipo de combu
-
stible utilizado:
- GAS (metano) versión GI 1000 DSPGN
- GASÓLEO versión GI 1000 DSPG
- FUEL (viscosidad máx. 50 °E a 50 °C) versión GI 1000 DSPN-D
- GAS (metano)/FUEL (viscosidad máx. 5 °E a 50 °C) versión GI-
Mist 1000 DSPNM
- GAS (metano)/GASÓLEO versión GI-Mist 1000 DSPGM
Los quemadores GI-Mist 1000 DSPGM y GI-Mist 1000 DSPNM
funcionan con metano o con combustible líquido.
- La relación de modulaciones del quemador “GI 1000” es 1 a 4.
La potencia térmica se ajusta mediante una sonda situada en
la caldera que controla el servomotor que regula la mezcla aire
comburente/combustible.
- El quemador está dotado con un dispositivo que hace variar
automáticamente el canal de paso del aire del cabezal de combu
-
stión en proporción a la carga. Con este dispositivo se consigue
una combustión perfecta con cualquier condición de carga. La
calidad de la mezcla aire/combustible mejora porque el exceso
de aire disminuye.
FIJACIÓN DEL QUEMADOR EN LA CALDERA
Para fijar el quemador en la placa de hierro de la caldera hay que
montar en primer lugar los prisioneros en la placa respetando la
plantilla de perforación.
Se aconseja soldarlos eléctricamente en la parte interna de la
placa para no extraerlos junto a las tuercas de bloqueo cuando se
desmonte el quemador. Si la placa no dispone de aislante térmico,
hay que colocar uno de 10 mm de espesor como mínimo entre la
placa y la caldera. El cabezal de combustión debe colocarse en el
hogar de la caldera a la altura indicada por el fabricante.
CONEXIONES ELÉCTRICAS
Es aconsejable que todas las conexiones se realicen con hilo
eléctrico flexible.
Las líneas eléctricas tienen que estar alejadas convenientemente
de las partes calientes.
Asegurarse de que la línea eléctrica a la que se conectará el aparato
esté alimentada con valores de tensión y frecuencia adecuados
al quemador. Asegurarse de que tanto la línea principal, como
el interruptor con fusibles (indispensable) y el eventual limitador
sean adecuados a soportar la corriente máxima absorbida por
el quemador.
Para mayor información ver los esquemas eléctricos específicos
para cada quemador en concreto.
Содержание GI 1000 DSPN-D
