Baker Hughes Druck DPI 610 IS Скачать руководство пользователя страница 68

Страница: 68 / 76

58 | DPI 610/615 IS Instruction Manual–English

Chapter

Hydraulic Calibrator Versions

7. Switch the instrument

and, still using the priming pump (2), pressurize the system to

approximately 2 bar (30 psi).

8. Close the isolation valve (6) disconnect the bleed hose assembly (1) from the priming port.

9.5 Operation

To obtain a pressure reading, proceed as follows:
1. Switch the instrument

and select the required

TASK

2. Rotate the screw-press clockwise to increase the applied pressure.

Note:

When hydraulic fluid is compressed and flows through a restriction, there is an

increase in temperature that affects the pressure. Allow sufficient time for this pressure

reading to stabilize before recording or logging a reading.

3. After testing, reduce the pressure in the system to zero by turning the screw-press counter

clockwise. Before disconnecting the UUT, open the isolation valve.

4. Remove the connection to the UUT and fit a blanking plug into the instrument’s pressure

port. Clean any spilled fluid off the instrument case.

9.6 Draining the Hydraulic Fluid

To drain the hydraulic fluid from the instrument, proceed as follows:
1. Turn the isolation valve (4) fully counter clockwise. Turn the instrument onto the left hand

side (pressure port nearest to the work bench). Place receptacle below the pressure port to

collect hydraulic fluid.

2. Drain the system by slowly winding in the screw-press (3) and then depressing the priming

pump (2) plunger to expel any fluid remaining in the instrument.

3. If necessary, apply an air line to the priming port to clear any remaining fluid out of the

instrument.

9.7 Flushing - Refilling or Changing the Hydraulic Fluid

If necessary, to remove any contaminants, flush out the hydraulic system as follows:

Содержание Druck DPI 610 IS







































































Результаты поиска

Содержание Druck DPI 610 IS

Отзывы:

Похожие инструкции для Druck DPI 610 IS

Бренды по названию

Популярные бренды

Baker Hughes Druck DPI 610 IS, Инструкция по эксплуатации

Результаты поиска

Содержание Druck DPI 610 IS

Отзывы:

Похожие инструкции для Druck DPI 610 IS

Бренды по названию

Популярные бренды