Baker Hughes Druck DPI 610 IS Скачать руководство пользователя страница 17

Страница: 17 / 76

English–DPI 610/615 IS Instruction Manual | 7

Fitting Batteries

2. Getting Started

2.1 Fitting Batteries

2.2 Switching On

Press the

I/O

switch on the front panel and proceed as follows:

The first time that the instrument is powered up, it will power-up in

BASIC

mode with the main

screen displaying voltage in the input display area and pressure in the source display area. To

switch to

Current

as input, press

as shown. Similarly,

to return to

Voltage

Note:

No other keys are active in this mode and the instrument can only be reconfigured by

pressing the

TASK

key and selecting another mode.

Cover fixing screws.

Six alkaline C cells, see table. Only use the battery type in the table.

Low battery indication.

WARNING

Batteries must only be fitted in a safe area.

Use only the batteries specified in “Batteries” on page

ii.

CAUTION

Old batteries can leak and cause corrosion. Never leave discharged

batteries in the instrument. Old batteries should be treated as hazardous waste

and disposed of accordingly.

PRESSURE INT

VOLTAGE

CURRENT

PRESSURE

UNITS

TASK : BASIC

Содержание Druck DPI 610 IS







































































Результаты поиска

Содержание Druck DPI 610 IS

Отзывы:

Baker Hughes Druck DPI 610 IS, Инструкция по эксплуатации, Страница: 17 / 76

Результаты поиска

Содержание Druck DPI 610 IS

Отзывы: