Azbil MagneW FLEX+ Скачать руководство пользователя страница 45

Страница: 45 / 88

Azbil Corporation

Installation

MagneW

FLEX+/PLUS+

Electromagnetic Flowmeter Detector

2-19

2.4.9: Installation on a PVC pipe using SUS grounding

ring material

The installation methods described in this section are for installation on a PVC pipe

using SUS grounding ring material. For the installation method corresponding to any

other combination of materials, refer to Table 2-5 on page 2-12.
PTFE gaskets are provided for this type of installation. If you supply the gaskets,

Azbil Corporation recommends non-rubber gaskets such as joint sheet or PTFE.

Although rubber gaskets can be used, they are not recommended. See page 2-21 for

installation using rubber gaskets.

CAUTION

The use of rubber gaskets and a lower fastening torque is not recommended and

can cause insufficient surface pressure between the lining and the grounding ring,

resulting in leakage.

If tightening the bolts at the specified torque threatens to warp or damage the PVC

pipes, you will need to use a protective plate. See page 2-20 for installation of the

protective plate.

To install a wafer detector on a PVC pipe using SUS grounding ring material

with a specified fastening torque:

• Install the detector as shown in the following illustration. The torque level for

tightening the bolts is not related to the gasket material.
See Table 2-1 on page 2-7 for the appropriate torque.
See Table 2-2 on page 2-10 for the inner diameter of the gasket.

Lining

Gasket

Grounding ring

Figure 2-15 Installation on a PVC pipe using SUS grounding ring material

Содержание MagneW FLEX+

























































































Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды

Azbil MagneW FLEX+, Руководство пользователя

Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды