Azbil MagneW FLEX+ Скачать руководство пользователя страница 65

Страница: 65 / 88

Azbil Corporation

Installation

MagneW

FLEX+/PLUS+

Electromagnetic Flowmeter Detector

2-39

2.5.7: Installation on a PVC pipe using non-SUS

grounding ring material

The installation methods described in this section are for installation on a PVC pipe

using non-SUS grounding ring material. For the installation method corresponding to

any other combination of materials, refer to Table 2-5 on page 2-12.
PTFE gaskets are provided for this type of installation. If you supply the gaskets,

Azbil Corporation recommends non-rubber gaskets such as joint sheet or PTFE.

When using rubber gaskets, gaskets of the same material with two different

thicknesses (0.5 to 1.0 mm (0.02 to 0.04 inch) and 3.0 to 4.0 mm (0.12 to 0.16

inch)) are required. See Table 2-3 on page 2-11 and Table 2-4 on page 2-11 for the

appropriate dimensions. See page 2-42 for installation using rubber gaskets.

CAUTION

The use of rubber gaskets and a lower fastening torque is not recommended and

can cause insufficient surface pressure between the lining and the grounding ring,

resulting in leakage.

If tightening the bolts at the specified torque threatens to warp or damage the PVC

pipes, you will need to use a protective plate. See page 2-41 for installation of the

protective plate.

Содержание MagneW FLEX+

























































































Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды

Azbil MagneW FLEX+, Руководство пользователя

Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды