manualshive.com logo in svg

Azbil MagneW FLEX+, Руководство пользователя

Поделиться
Скачать
Azbil MagneW FLEX+ Скачать руководство пользователя страница 19

Azbil Corporation 

Introduction

MagneW 

FLEX+/PLUS+

 Electromagnetic Flowmeter Detector 

1-5

1.3.1: Wafer type detector

A wafer detector consists of the components shown in the figure below.

Grounding terminal

Waterproof gland

Terminal box cover

Terminal box

Grounding ring

Electrode cover

Mounting screw (4 places)

Flow direction mark

Figure 1-4  Wafer detector main parts

Name

Function

Flow direction mark

Indicates the direction of fluid flow. 

Mount the detector so that the measured fluid flows in the 

direction indicated by this mark.

Electrodes

Detect an electromagnetic force signal proportional to the 

flow rate of the fluid passing through the detector.

The electrode material varies depending on the corrosion 

characteristics of the fluid to be measured.

Electrode cover

Houses the electrodes. Do not remove the cover with the 

detector installed on a pipe.

Grounding rings

Keep reference voltage as zero by grounding the unit. 

The grounding ring material varies depending on the 

corrosion characteristics of the fluid to be measured.

Terminal box

(Remote model only)

Houses the connection terminals used for applying 

a standard voltage. Houses the excitation and signal 

terminals.

Terminal box cover 

(Remote model only)

Keeps the terminals dry and protected. Keep the terminal 

box cover on during operation.

Содержание MagneW FLEX+

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды