manualshive.com logo in svg

Azbil MagneW FLEX+, Руководство пользователя

Поделиться
Скачать
Azbil MagneW FLEX+ Скачать руководство пользователя страница 40

Installation 

Azbil Corporation

2-14 MagneW 

FLEX+/PLUS+

 Electromagnetic Flowmeter Detector

2.4.6: Installation on a vertical pipe

Follow this procedure to install the detector on a horizontal pipe.

Step

Action

Drawing

1

• 

Of the flange holes shown by black dots in the 

drawing, insert through-bolts into the two holes 

at the back and fasten them lightly with nuts. 

Slip one centering nut onto each through bolt 

before inserting the bolts.

Flange

Terminal

box side

Back

Centering nuts

2

• Turn the detector so that the direction mark on 

the detector matches the direction of fluid flow.

• Insert the detector and gaskets between the pipe 

flanges.

Gaskets

Direction of

fluid flow

3

• 

Insert through-bolts fitted with one centering 

nut each into the remaining two flange holes 

shown by black dots in steps 1 and 2.

Gaskets

Direction of

fluid flow

4

• Make sure that the detector remains properly 

centered.

• Make sure that the gaskets do not protrude 

beyond the edges of the pipe flanges.

• When you have checked these items, insert 

the remaining through-bolts into the flange 

holes and tighten the bolts evenly using the 

appropriate fastening torque given on page 

2-7.

Содержание MagneW FLEX+

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды