Azbil MagneW FLEX+ Скачать руководство пользователя страница 76

Страница: 76 / 88

Installation

Azbil Corporation

2-50 MagneW

FLEX+/PLUS+

Electromagnetic Flowmeter Detector

15 mm

(0.59 inch)

C-wire

Inside

shield

White

C-wire

Black

15 mm

(0.59 inch)

Inside

sheath

Figure 2-42 Trimming the inside sheath

(6) Wind each lead wire (SA and SB) around the inside shield once.
(7) Solder the lead wired (SA and SB) to the middle of this 5 mm (0.2 inch) length.

Be sure to keep the two inside shields separate from each other to prevent them

from being bonded together by mistake during soldering. The length of the lead

wires should be measured from this point. Make the length of the lead wires

slightly longer than necessary (see the operating manuals for the products) and

trim to the specified length in Step 10.

5 mm

(0.2 inch)

C-wire

Inside

shield

Inside

shield

5 mm

(0.2 inch)

C-wire

SA-wire

SB-wire

A-wire

B-wire

Attach the wire to the

middle of this 5 mm

(0.2 inch) length.

Figure 2-43 Attaching the lead wires (SA and SB)

CAUTION

Be sure to use adequate solder so that contact failure will not occur between the

C -wire and the outside shield. If the soldering connection is insecure, noise is

generated due to contact resistance.

(8)

Cut the inside shield off at a point 5 mm (0.2 inch) from the inside sheath.

CAUTION

Do not cut into the conductive tube.

Содержание MagneW FLEX+

























































































Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды

Azbil MagneW FLEX+, Руководство пользователя

Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды