Azbil MagneW FLEX+ Скачать руководство пользователя страница 42

Страница: 42 / 88

Installation

Azbil Corporation

2-16 MagneW

FLEX+/PLUS+

Electromagnetic Flowmeter Detector

2.4.8: Installation on a metal pipe using non-SUS

grounding ring material

The installation methods described in this section are for installation on a metal pipe

using non-SUS grounding ring material. For the installation method corresponding to

any other combination of materials, refer to Table 2-5 on page 2-12.
PTFE gaskets are provided for this type of installation. Although rubber gaskets

can be used, it is not possible to reduce the fastening torque. See page 2-17 for

installation using rubber gaskets.

CAUTION

The use of anything other than the PTFE gaskets provided can result in leakage.
The use of rubber gaskets is not recommended and can cause leakage.

To install a wafer detector on a metal pipe using non-SUS grounding ring

material and a specified torque:

• Install the detector as shown in the following illustration. The torque level for

tightening the bolts is not related to the gasket material.
See Table 2-1 on page 2-7 for the appropriate torque.
See Table 2-2 on page 2-10 for the inner diameter of the gasket.

Lining

Grounding ring

PTFE gasket

Figure 2-12 Installation on a metal pipe using non-SUS grounding ring material

and a specified torque

Содержание MagneW FLEX+

























































































Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды

Azbil MagneW FLEX+, Руководство пользователя

Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды