manualshive.com logo in svg

Azbil MagneW FLEX+, Руководство пользователя

Поделиться
Скачать
Azbil MagneW FLEX+ Скачать руководство пользователя страница 36

Installation 

Azbil Corporation

2-10 MagneW 

FLEX+/PLUS+

 Electromagnetic Flowmeter Detector

Gaskets

Gaskets are supplied with the grounding ring, except when it is made of SUS 

material. If you are using SUS material, you must provide the gaskets. Azbil 

Corporation recommends joint sheet or polytetraflouroethylene (PTFE) gasket 

material. For the inner (bore) diameters of the gaskets, see the following table. 

Rubber gaskets are not recommended.

 CAUTION

Using a gasket with too small a diameter can affect the flow velocity distribution, 

resulting in inaccurate measurement.
Using a gasket with too large a diameter can cause leakage. Also, any solid 

substance in the fluid to be measured could accumulate between the gasket and the 

flange, resulting in inaccurate measurement.

Table 2-2  Recommended inner diameters of gaskets

Nominal 

detector 

bore 

diameter

mm

2.5 5

10 15 25 40 50 65 80 100 125 150 200

(inch)

0.1 0.2 3/8 1/2 1

1½ 2

2½ 3

4

5

6

8

Gasket 

inner 

diameter

mm

±

6

1

6

1

11

1

16

1

25

1

40

1

51

1

64

1

76

1

101

1

124

1

148

1

196

1

(inch)

±

0.24

0.04

0.24

0.04

0.43

0.04

0.63

0.04

0.98

0.04

1.57

0.04

2.01

0.04

2.52

0.04

2.99

0.04

3.98

0.04

4.88

0.04

5.83

0.04

7.72

0.04

If you install the detector at a lower torque level using rubber gaskets, you must use 

gaskets with the bore and outer diameters for the respective pipe bore shown in the 

following table. Depending on the grounding ring material, two gaskets of different 

thicknesses may be required. The following two tables provide the inner and outer 

diameters for the two different gasket thicknesses.

Содержание MagneW FLEX+

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды