Azbil MagneW FLEX+ Скачать руководство пользователя страница 79

Страница: 79 / 88

Azbil Corporation

Installation

MagneW

FLEX+/PLUS+

Electromagnetic Flowmeter Detector

2-53

Dressing the dedicated cable : Detector side

To dress the dedicated cable:
(1)

Scribe (cut) a line in the outside sheath (black) as shown in the following figure

and remove the sheathing. The length is 75mm (2.95 inch).

CAUTION

Do not cut into the outside shield.

75 mm (2.95inch)

Outside shield

Outside sheath (black)

Figure 2-48 Trimming the outside sheath

~Note

If the terminal of the converter is designed not to use a shield drive,

remove the outside shield and skip to Step 4.

(2) Wind the lead wire once around the outside shield.
(3) Solder the lead wire (C-wire) to the middle of the 5 mm (0.2 inch) length. Make

the length of the lead wire slightly longer than necessary and trim it to the

specified length in Step 10.

5 mm

(0.2 inch)

Attach the lead wire

to the middle of this

5 mm (0.2 inch) length.

Outside

shield

C-wire

Lead wire

Outside

sheath

5 mm

(0.2 inch)

Figure 2-49 Attaching the C-wire

CAUTION

Be sure to use adequate solder so that contact failure will not occur between the

C-wire and the outside shield. If the soldering connection is insecure, noise is

generated due to contact resistance.

~Note

If the outside shield is not allowed to bend during soldering, in some

cases, the conductive tube cannot be peeled off due to the heat of the

solder.

Содержание MagneW FLEX+

























































































Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды

Azbil MagneW FLEX+, Руководство пользователя

Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды