Azbil MagneW FLEX+ Скачать руководство пользователя страница 77

Страница: 77 / 88

Azbil Corporation

Installation

MagneW

FLEX+/PLUS+

Electromagnetic Flowmeter Detector

2-51

5 mm (0.2 inch)

C-wire

SA-wire

SB-wire

A-wire

B-wire

5 mm (0.2 inch)

C-wire

SA-wire

SB-wire

A-wire

B-wire

Conductive

tube

Conductive

tube

Figure 2-44 Trimming the inside shield

(9)

Peel off the conductive tube (black) completely up to the inside shield.

C-wire

SA-wire

SB-wire

A-wire

B-wire

Insulator

C-wire

SA-wire

SB-wire

A-wire

B-wire

Conductive

tube

Conductive

tube

Figure 2-45 Removing the conductive tube

(10) Trim the insulator to within 5 mm (0.2 inch) from its end. Trim the other lead

wires (soldered to the shield sections) to the specified lengths so that each

conductive wire is exposed by 5 mm (0.2 inch).

5 mm

(0.2 inch)

C-wire

SA-wire

SB-wire

A-wire

B-wire

Insulator

5 mm

(0.2 inch)

C-wire

SA-wire

SB-wire

A-wire

B-wire

Conductive wire

Figure 2-46 Trimming the insulator

(11) Wind insulating tape around each inside shield and then around each outside

shield.

(12) Attach markers to the lead wires.
(13) Crimp the terminals onto each lead wire. Test each terminal by pulling on it to

make sure the terminal will not come off.

~Note

In some cases, the C -wire must be crimped together with either the

SA or SB lead wire. For further information, refer to the appropriate

operation manuals.

Содержание MagneW FLEX+

























































































Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды

Azbil MagneW FLEX+, Руководство пользователя

Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды