Azbil MagneW FLEX+ Скачать руководство пользователя страница 6

Страница: 6 / 88

Safety

Azbil Corporation

iv MagneW

FLEX+/PLUS+

Electromagnetic Flowmeter Detector

CAUTION

Tighten each bolt a little at a time and apply uniform pressure to all the bolts.

If leakage continues after tightening the bolts, make sure that the pipe is not off

center, then continue to tighten each bolt a little at a time.

CAUTION

Using a gasket with too small a diameter can affect the flow velocity distribution,

resulting in inaccurate measurement.
Using a gasket with too large a diameter can cause leakage. Also, any solid

substance in the fluid to be measured could accumulate between the gasket and the

flange, resulting in inaccurate measurement.

CAUTION

The necessary materials and the installation method vary according to the material

of the ring and that of the pipe on which the detector is to be installed. Select the

appropriate method of installation from the following table after confirming the

specifications of the detector to be installed and the conditions of installation.

Improper installation can result in leakage or damage to the pipe flanges.

CAUTION

The use of anything other than the PTFE gaskets provided can result in leakage.
The use of rubber gaskets is not recommended and can cause leakage.

CAUTION

The use of rubber gaskets and a lower fastening torque is not recommended and

can cause insufficient surface pressure between the lining and the grounding ring,

resulting in leakage.

CAUTION

Insufficient grounding can cause output fluctuations, instability of the zero point,

or output drift. Secure single point grounding with a grounding resistance of 100

or less is recommended.

Do not ground a welder to the detector to avoid damaging the detector.

Содержание MagneW FLEX+

























































































Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды

Azbil MagneW FLEX+, Руководство пользователя

Результаты поиска

Содержание MagneW FLEX+

Отзывы:

Бренды по названию

Популярные бренды