manualshive.com logo in svg

Azbil MagneW FLEX+, Руководство пользователя

Поделиться
Скачать
Azbil MagneW FLEX+ Скачать руководство пользователя страница 20

Introduction 

Azbil Corporation

1-6 MagneW 

FLEX+/PLUS+

 Electromagnetic Flowmeter Detector

1.3.2: Flange type detector

A Flange detector consists of the components shown in the figure below.

Mounting screw

(4 places)

Electrode cover

Waterproof gland

Grounding terminal 

Terminal box cover

Terminal box

Flow direction mark

Flange

Grounding ring

Figure 1-5  Flange detector main parts

Name

Function

Flow direction mark

Indicates the direction of fluid flow. Mount the detector 

so that the measured fluid flows in the direction indicated 

by this mark.

Electrodes

Detect an electromagnetic force signal proportional to 

the flow rate of the fluid passing through the detector. 

The electrode material varies depending on the corrosion 

characteristics of the fluid to be measured.

Electrode cover

Houses the electrodes. Do not remove the cover with the 

detector installed on a pipe.

Grounding rings

Keep reference voltage as zero by grounding the unit. 

The grounding ring material varies depending on the 

corrosion characteristics of the fluid to be measured.

Terminal box

(Remote model only)

Houses the connection terminals used for applying 

a standard voltage. Houses the excitation and signal 

terminals.

Terminal box cover 

(Remote model only)

Keeps the terminals dry and protected. Keeps the 

terminal box cover on during operation.

Содержание MagneW FLEX+

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды