background image

 

 

 
   

AW86225 

October  2021  V1.9 

 

www.awinic.com

                                                    41                          Copyright © 2020 SHANGHAI AWINIC TECHNOLOGY CO., LTD 

 

Disclaimer 

Information in this document is believed to be accurate and reliable. However, Shanghai AWINIC Technology 
Co., Ltd (AWINIC Technology) does not give any representations or warranties, expressed or implied, as to 
the accuracy or completeness of such information and shall have no liability for the consequences of use of 
such information. 

AWINIC Technology reserves the right to make changes to information published in this document, including 
without  limitation  specifications  and  product  descriptions,  at  any  time  and  without  notice.  Customers  shall 
obtain the latest relevant information before placing orders and shall verify that such information is current and 
complete. This document supersedes and replaces all information supplied prior to the publication hereof. 

AWINIC  Technology  products  are  not  designed,  authorized  or  warranted  to  be  suitable  for  use  in  medical, 
military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an AWINIC 

Technology  product  can  reasonably  be  expected  to  result  in  personal  injury,  death  or  severe  property  or 
environmental  damage.  AWINIC  Technology  accepts  no  liability  for  inclusion  and/or  use  of  AWINIC 
Technology  products  in  such  equipment  or  applications  and  therefore  such  inclusion  and/or  use  is  at  the 
customer’s own risk. 

Applications  that  are  described  herein  for  any  of  these  products  are  for  illustrative  purposes  only.  AWINIC 
Technology makes no representation or warranty that such applications will be suitable for the specified use 
without further testing or modification. 
All products are sold subject to the general terms and conditions of commercial sale supplied at the time of 
order acknowledgement. 

Nothing  in  this  document  may  be  interpreted  or  construed  as  an  offer  to  sell  products  that  is  open  for 
acceptance  or  the  grant,  conveyance  or  implication  of  any  license  under  any  copyrights,  patents  or  other 
industrial or intellectual property rights. 

Reproduction of AWINIC information in AWINIC data books or data sheets is permissible only if reproduction 
is  without  alteration  and  is  accompanied  by  all  associated  warranties,  conditions,  limitations,  and  notices. 
AWINIC is not responsible or liable for such altered documentation. Information of third parties may be subject 
to additional restrictions. 

Resale of AWINIC components or services with statements different from or beyond the parameters stated by 
AWINIC for that component or service voids all express and any implied warranties for the associated AWINIC 
component or service and is an unfair and deceptive business practice. AWINIC is not responsible or liable for 
any such statements. 

awinic Confidential

Содержание AW86225










































Отзывы: