manualshive.com logo in svg

Avidyne FlightMax EX500, Руководство по установке

Поделиться
Скачать
Avidyne FlightMax EX500 Скачать руководство пользователя страница 120

 

Installation Manual

 

 

P/N 600-00175-000 Rev 04

- 110 -

ANY PRODUCT COMPONENT SUPPLIER'S RESPONSIBILITY OR LIABILITY WILL IN ANY WAY BE ENLARGED OR OTHERWISE 
ALTERED DUE TO AVIDYNE'S PROVISION OF TECHNICAL SUPPORT OR TRAINING RELATED TO THE PRODUCT.
WITHOUT LIMITING THE FOREGOING, NEITHER AVIDYNE (NOR ITS AFFILIATES) MAKE ANY REPRESENTATIONS, AFFIRMATIONS 
OR WARRANTIES REGARDING OR RELATED TO PRODUCTS NOT MANUFACTURED BY AVIDYNE OR REGARDING OR RELATED TO 
THE PERFORMANCE OR RELIABILITY OF ANY SUCH PRODUCT, EITHER ALONE OR WHEN USED WITH ANY PRODUCT 
MANUFACTURED BY AVIDYNE, OR THE SUITABILITY OF ANY SUCH PRODUCT FOR USE WITH ANY PRODUCT MANUFACTURED BY 
AVIDYNE.  AVIDYNE (AND ITS AFFILIATES) EXPRESSLY DISCLAIM ANY AND ALL REPRESENTATIONS, AFFIRMATIONS AND/OR 
WARRANTIES REGARDING OR RELATED TO ANY SUCH PRODUCTS.  IN NO EVENT WILL AVIDYNE (OR ITS AFFILIATES) BE 
RESPONSIBLE OR LIABLE FOR ANY DAMAGE OF ANY NATURE WHATSOEVER, INCLUDING DIRECT, INDIRECT, INCIDENTAL, 
CONSEQUENTIAL, SPECIAL, LOSS OF USE, LOSS OF REVENUE OR PROFIT, PROPERTY DAMAGE, PERSONAL INJURY, 
WRONGFUL DEATH, OR OTHER DAMAGE (WHETHER OR NOT AVIDYNE (OR ITS AFFILIATES) WERE NOTIFIED OF THE POSSIBILITY 
THAT ANY DAMAGE MIGHT BE INCURRED), ARISING OUT OF OR RELATED TO PRODUCTS NOT MANUFACTURED BY AVIDYNE, 
THE PURCHASE OR SALE OF SUCH PRODUCTS, THEIR PERFORMANCE OR RELIABILITY, EITHER ALONE OR WHEN USED WITH 
ANY PRODUCT MANUFACTURED BY AVIDYNE, OR THE SUITABILITY OF ANY SUCH PRODUCT FOR USE WITH ANY PRODUCT 
MANUFACTURED BY AVIDYNE.
THIS EXCLUSIVE LIMITED WARRANTY ALSO APPLIES IN LIEU OF AND EXPRESSLY SUPERCEDES AND EXCLUDES ALL OTHER 
RIGHTS ANY PURCHASER HAS OR MAY HAVE RELATED TO THE PRODUCT AND/OR ARISING OUT OF OR RELATED TO ITS 
PURCHASE, SALE, PERFORMANCE, RELIABILITY OR USE, EITHER ALONE OR WITH ANY OTHER PRODUCT OR PRODUCTS, 
WHETHER IN CONTRACT, IN TORT (INCLUDING RIGHTS SOUNDING IN NEGLIGENCE, STRICT LIABILITY AND 
MISREPRESENTATION), UNDER STATUTE, AT LAW, IN EQUITY, OR OTHERWISE, AND PURCHASER EXPRESSLY AND KNOWINGLY 
WAIVES ALL SUCH RIGHTS TO THE FULLEST EXTENT PERMITTED BY LAW.  PURCHASER ALSO EXPRESSLY AND KNOWINGLY 
AGREES THAT THE PRODUCT IS NOT A CONSUMER GOOD.
THE FOREGOING PARAGRAPHS DEFINE AND LIMIT AVIDYNE'S SOLE RESPONSIBILITY AND LIABILITY AND PURCHASER'S SOLE 
AND EXCLUSIVE REMEDIES RELATED TO THE PRODUCT.
Some jurisdictions may not allow the exclusion or limitation of warranties or liabilities, in which case the above limitations or exclusions, or some 
of them, may not apply in those jurisdictions.

Software License

Avidyne Corporation (“Avidyne”) is willing to license this software, pilot's guide, and related materials (the “Software”) only on the 

condition that you agree to all the terms of this agreement. Please read these terms carefully.

Trademarks

Avidyne and the Avidyne logo are trademarks of Avidyne Corporation. Other brands or products are the trademarks or registered 

trademarks of their respective holders and should be treated as such.

License and Certain Restrictions

You may use the Software on the EX500 or EX600 on which it was delivered. You may not copy the Software for any purpose. 

You may not transfer the Software or any rights under this Agreement to another party without this Agreement. The other party 

must agree to accept the terms of this Agreement. The Software contains trade secrets. You may not decompile, reverse 

engineer, disassemble, or otherwise reduce the Software to human-readable form. You may not modify, adapt, translate, rent, 

sublicense, assign, lease, loan, resell for proof, distribute, or network the Software, disk or related materials or create derivative 

works based upon the software or any part thereof. Title, ownership rights, and intellectual property rights in and to the Software 

belongs to Avidyne and its licensors. The Software is protected by the copyright laws of the United States and by international 

copyright treaties. Title, ownership rights and intellectual property rights in and to the content accessed through the Software is the 

property of Avidyne, and where applicable, to the licensor content owners and may be protected by applicable copyright or other 

law. This Agreement gives you no rights to such content.

Note, the Software includes an internal capability to record certain of the operations and data generated by or provided to the 

EX500 or EX600, hereinafter referred to as "data files".  These data files are an integral part of the Software as they assist 

Avidyne in testing and assessing the performance of the Software and the EX500 or EX600.  You agree in partial consideration for 

this license that such data files are the property of Avidyne and that you will neither tamper with nor destroy such data files.  

Further you agree to make such data files (or the EX500 or EX600) available to Avidyne at reasonable times and upon reasonable 

notice.  Avidyne will endeavor to keep the information contained in the data files confidential, except to the extent required by 

reasonable exercise of its obligations to the FAA or other governmental agency or as a part of a court order.  Avidyne makes no 

commitment to review or share the information contained within the data files with you, and you agree that you have no 

expectation that this information will be reviewed or shared.

Содержание FlightMax EX500





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды