Autel MaxiPRO MP808S Скачать руководство пользователя

Страница: 7 / 89

Using this Manual

This manual contains device usage instructions for the Autel MaxiPRO MP808S.

Some illustrations shown in this manual may contain modules and optional equipment
that are not included in your system.

1.1 Conventions

The following conventions are used:

Bold Text

Bold text is used to highlight selectable items such as buttons and menu options.

Example:



Tap

Notes and Important Messages

Notes

NOTE

provides helpful information such as additional explanations, tips, and

comments.

Example:

NOTE

New batteries reach full capacity after approximately 3 to 5 charging and discharging
cycles.

Important

IMPORTANT

indicates a situation which, if not avoided, may result in damage to the

tablet or vehicle.

Example:

IMPORTANT

Keep the cable away from heat, oil, sharp edges and moving parts. Replace damaged
cables immediately.

Содержание MaxiPRO MP808S


























































































Результаты поиска

Содержание MaxiPRO MP808S

Отзывы:

Похожие инструкции для MaxiPRO MP808S

Бренды по названию

Популярные бренды

Autel MaxiPRO MP808S, Руководство пользователя

Результаты поиска

Содержание MaxiPRO MP808S

Отзывы:

Похожие инструкции для MaxiPRO MP808S

Бренды по названию

Популярные бренды