Autel MaxiPRO MP808S Скачать руководство пользователя

Страница: 10 / 89

A. Green



Illuminates green when the tablet is charging and the battery level is above 90%.



Illuminates green when the tablet is powered on and the battery level is above
15%.

B. Yellow



Illuminates yellow when the tablet is charging and the battery level is below 90%.

C. Red



Illuminates red when the tablet is powered on and the battery level is below 15%
or an error has occurred.

Figure 2-2

Tablet Top View

5. Mini USB Port

6. Micro SD Card Slot

— holds the micro SD card.

7. DB15-Pin Port

— connects the main cable.

8. USB Port

9. Power/Lock Button

— press and hold to turn the tablet on/off or tap to unlock the

tablet.

Figure 2-3

Tablet Rear View

10. Heat Sink

11. Collapsible Stand

— extends from the back to allow hands-free viewing of the tablet.

Содержание MaxiPRO MP808S


























































































Результаты поиска

Содержание MaxiPRO MP808S

Отзывы:

Похожие инструкции для MaxiPRO MP808S

Бренды по названию

Популярные бренды

Autel MaxiPRO MP808S, Руководство пользователя

Результаты поиска

Содержание MaxiPRO MP808S

Отзывы:

Похожие инструкции для MaxiPRO MP808S

Бренды по названию

Популярные бренды