manualshive.com logo in svg

AUMA SARVEx 07.2, Руководство по эксплуатации

Поделиться
Скачать
AUMA SARVEx 07.2 Скачать руководство пользователя страница 7

1.3.

Warnings and notes

The following warnings draw special attention to safety-relevant procedures in these
operation instructions, each marked by the appropriate signal word (DANGER,
WARNING, CAUTION, NOTICE).

Indicates an imminently hazardous situation with a high level of risk. Failure
to observe this warning results in death or serious injury.

Indicates a potentially hazardous situation with a medium level of risk. Failure
to observe this warning could result in death or serious injury.

Indicates a potentially hazardous situation with a low level of risk. Failure to
observe this warning could result in minor or moderate injury. May also be
used with property damage.

Potentially hazardous situation. Failure to observe this warning could result
in property damage. Is not used for personal injury.

Safety alert symbol 

 warns of a potential personal injury hazard.

The signal word (here: DANGER) indicates the level of hazard.

1.4.

References and symbols

The following references and symbols are used in these instructions:

Information

The term Information preceding the text indicates important notes and information.

Symbol for CLOSED (valve closed)

Symbol for OPEN (valve open)

Via the menu to parameter

Describes the menu path to the parameter. When using the push buttons of local
controls, the required parameter can be quickly found on the display. Display texts
are shaded in grey:

Display

.

➥

Result of a process step

Describes the result of a preceding process step.

Warning signs at the device

The following warning signs can be attached to the device.

General warning sign

General warning of a danger zone.

Hot surface

Warning of hot surfaces, e.g. possibly caused by high ambient temperatures or strong
direct sunlight.

Electrical voltage

Hazardous voltage! Warning of electric shock. At some devices, the warning sign
additionally includes a time interval, e.g. 30 s. Once power supply is switched off,
you will have to wait for the indicated period. Only then may the device be opened.

7

SAVEx 07.2 – SAVEx16.2/SARVEx 07.2 – SARVEx16.2 Control unit: electronic (MWG)
ACVExC 01.2 Non-Intrusive

Safety instructions

Содержание SARVEx 07.2





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды