AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 96

AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 77

Ò

Check wiring.

P-FEEDBACK E4 LOSS

Signal loss of process feedback E4 (only if process controller of logic
sub-assembly is available and active).

Ò

Check wiring.

FIBRE OPTIC LOSS

Signal loss of fibre optic cable (only for bus with fibre optic loop topology).

Ò

Check wiring.

ANALOG IN1 BUS1 LOSS

Signal loss of analogue input 1.

Ò

Check wiring.

ANALOG IN2 BUS1 LOSS

Signal loss of analogue input 2.

Ò

Check wiring.

8.1.4 Status indication S3 - causes for not ready remote

The causes for the

NOT READY IND.

fault signals (status indication

S0

)

are indicated within this group.

È

Description of the fault indications:

READY

Actuator can be operated from REMOTE.

NOT REMOTE

Actuator cannot be operated from REMOTE.
Possible causes:
Selector switch in position LOCAL or OFF.

WRONG COMMAND

Indicates the fact that several operation commands were received simulta-
neously via the fieldbus (e.g. REMOTE OPEN and REMOTE CLOSE simul-
taneously or REMOTE CLOSE/REMOTE OPEN and REMOTE SETPOINT
(nominal) simultaneously) or that the max. value for a nominal position has
been exceeded.

EMERGENCY MODE

The operation mode EMERGENCY is active.

EXTERNAL CONTROLS BUS

For combination fieldbus/standard interface function:
Operation via parallel interface.

EMCY STOP ACTIVE

The EMERGENCY STOP button has been operated.

ACTUATOR LOCKED

The actuator is locked (only set for special applications, e.g. bypass func-
tion).

77

Actuator controls

Manual

AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus

NOT READY IND.

S3

READY

«
...
75
76
77
78
79
...
»

Содержание Aumatic AC 01.1

































































































Отзывы:

Нет отзывов