AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 65

Страница: 65 / 96

OPEN CLOSE STOP

Figure 15:

Actuator control is possible in open-close duty (OPEN – CLOSE -
STOP) only. Modulating duty is not possible.

Operation commands can be issued via the fieldbus or via the external
inputs. Switch-over is made via BUS/REMOTE input (see below).

Operation commands are made in self-retaining only.

Information

In the event of loss of bus communication, the external inputs do not auto-
matically take over!

Information

Please refer to the AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus
manual (Device integration Fieldbus) for details on feedback signals.

Switching between operation commands via fieldbus and external
inputs

Apply 0 V DC (input open) at BUS/REMOTE input:
Controls react to fieldbus signals only.

Apply + 24 V DC at BUS/REMOTE input.
Controls reacts to external input signals only:
MODE, CLOSE, OPEN, STOP, EMERGENCY, ANIN1 (the available
external inputs depend on the parameter setting).

Actuator controls

Manual

AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus

Figure 15

External inputs

Fieldbus interface

Содержание Aumatic AC 01.1

































































































Результаты поиска

Содержание Aumatic AC 01.1

Отзывы:

AUMA Aumatic AC 01.1, Руководство пользователя, Страница: 65 / 96

Результаты поиска

Содержание Aumatic AC 01.1

Отзывы: