AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 96

AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 50

7.6

Positioner (operation mode SETPOINT MODE)

The positioner records position setpoint E1 and position feedback E2 for
comparison. Depending on the detected deviation, the actuator motor then
runs in direction OPEN or CLOSE.

Ò

Set selector switch to position REMOTE.
If the positioner is active, the display shows:

Information

If the display shows

REMOTE MODE

, the actuator is set to open-close duty

and no modulation is performed. In this case, modulating duty has to be
selected first, refer to page 53.

Table of contents:
7.6.1 Adaptive behaviour: switch on or off
7.6.2 Overrun (inner dead band): manual setting
7.6.3 Max. error variable (outer dead band): manual setting
7.6.4 Dead time setting
7.6.5 Closing fully/opening fully (end position tolerance for setpoint E1)
7.6.6 Open-close and modulating duty selection
7.6.7 Source of setpoint E1: view
7.6.8 Input range of setpoint E1: view/edit

7.6.1 Adaptive behaviour: switch on or off

As standard, the adaptive positioning is switched on, i.e. overrun and max.
error variable are automatically defined by the positioner (figure 9).
If the setting is to be made manually, the

ADAPTIVE BEHAVIOUR

parame-

ter must be in position

OFF

.

Æ

Via the menu to parameter:

MAIN MENU (M0)

CONFIGURATION (M4)

SPECIAL FUNCTIONS (M40)

ADAPTIVE BEHAVIOUR (M4011)

Default value:

ON

È

Description of the parameter settings:

OFF

Adaptive behaviour switched off.

ON

Adaptive behaviour switched on.

50

Actuator controls
AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus

Manual

SETPOINT MODE

S0

E1

60%

E2

60%

SETPOINT POSITION

EDIT

M4011

ADAPTIVE BEHAVIOUR

ON

:EDIT

↵

:OK

C:ESC

«
...
48
49
50
51
52
...
»

Содержание Aumatic AC 01.1

































































































Отзывы:

Нет отзывов