AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 96

AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 43

7.4

Intermediate positions (option)

The AUMATIC allows to define up to 8 intermediate positions.

Condition

The actuator is either equipped with:

.

an MWG (for Non-Intrusive version), or

.

a potentiometer (5 k

Ω

) or

.

an RWG

In these versions, the positioning of the intermediate positions is made via
software parameters.

Selection of the intermediate positions can be made either via push buttons
from LOCAL or via the fieldbus interface from REMOTE with the standard
commands OPEN and CLOSE. The actuator stops when reaching the inter-
mediate position. The operation command has to be cleared and sent again
to resume operation to the next intermediate position.

Information

If the intermediate positions are to be approached directly (without stop), the
multiport valve function (page 47) is available as an option.

Table of contents:
7.4.1 Display indication: enable view
7.4.2 Intermediate positions: switch on or off
7.4.3 Intermediate position definition
7.4.4 Operation behaviour = actuator behaviour definition
7.4.5 Intermediate positions: set the signalling

7.4.1 Display indication: enable view

The

INTERMED. POSITION

parameter must be set to

VIEW ENABLED

to

carry out settings in the intermediate positions.

Æ

Via the menu to parameter:

MAIN MENU (M0)

CONFIGURATION (M4)

SPECIAL FUNCTIONS (M40)

INTERMED. POSITION (M4015)

Default value:

VIEW NOT ENABLED

Description of the parameter settings:

VIEW NOT ENABLED

The parameter for the intermediate positions are not indicated in the display.

VIEW ENABLED

The parameter for the intermediate positions are indicated in the display.

43

Actuator controls

Manual

AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus

EDIT

M4015

INTERMED. POSITION

VIEW NOT ENABLED

:EDIT

↵

:OK

C:ESC

«
...
41
42
43
44
45
...
»

Содержание Aumatic AC 01.1

































































































Отзывы:

Нет отзывов