AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 96

AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 48

7.5.2 Check: Positioner active?

The positioner must be available. This value is set in the factory.

Æ

Via the menu to parameter:

MAIN MENU (M0)

CONFIGURATION (M4)

SPECIAL FUNCTIONS (M40)

POSITIONER (M4000)

The

POSITIONER

parameter must be set to

POSITIONER ENABLED

.

È

Description of the parameter settings:

FUNCTION NOT ACTIVE

There is no positioner available.

POSITIONER ENABLED

The controls are equipped with a positioner.

7.5.3 Display indication: enable view

The indication of the multiport valve intermediate positions in the display is
performed as described on page 17.

7.5.4 Intermediate positions: switch on or off

The multiport valve intermediate positions are switched on/off as described
on page 44.

7.5.5 Intermediate position setting

Each of the 8 intermediate positions must be programmed. For direct selec-
tion of the intermediate positions from either LOCAL or REMOTE, it is suffi-
cient to define the position (

POS.1-8)

parameter of each intermediate

position.

Æ

Via the menu to parameter:

MAIN MENU

SETTINGS (M1)

INTERMED. POSITION (M1C)

POS.1 (M1C10)

Setting ranges:

0.0 %

to

100.0 %

of the travel (from OPEN to CLOSED)

Typically all 8 outputs of the valve are distributed evenly over 360°, therefore the
limit switch CLOSE should be set to output 1 and the limit switch OPEN to output
8. Afterwards the positions of the intermediate positions can be set:
Intermediate position 1:

POS.1

0.0 % (output 1)

Intermediate position 2:

POS.2

14.3 % (output 2)

Intermediate position 3:

POS.3

28.6 % (output 3)

Intermediate position 4:

POS.4

42.9 % (output 4)

Intermediate position 5:

POS.5

57.1 % (output 5)

Intermediate position 6:

POS.6

71.4 % (output 6)

Intermediate position 7:

POS.7

85.7 % (output 7)

Intermediate position 8:

POS.8

100.0 % (output 8)

48

Actuator controls
AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus

Manual

VIEW

POSITIONER

POSITIONER ENABLED

C:ESC

EDIT

M1C10

POS.1

0.0 %

:EDIT

↵

:OK

C:ESC

«
...
46
47
48
49
50
...
»

Содержание Aumatic AC 01.1

































































































Отзывы:

Нет отзывов