AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 54

Страница: 54 / 96

7.6.7 Source of setpoint E1: view

This value is set in the factory and can only be changed by the AUMA ser-
vice.

Via the menu to parameter:

MAIN MENU (M0)

CONFIGURATION (M4)

SETUP (M41)

SETPOINT E1 (M4100)

Default value:

FOUNDATION FIELDBUS

Description of the parameter settings:

NONE

There is no setpoint source available.

LOGIC ANALOG IN1

For AUMA service only (the setpoint E1 is transmitted from external via the
analogue input 1 directly to the logic board).

I/O1 ANALOG IN1

The setpoint E1 is transmitted via the I/O board interface, analogue input 1.

I/O1 ANALOG IN2

The setpoint E1 is transmitted via the I/O board interface, analogue input 2.

FOUNDATION FIELDBUS

The setpoint E1 is transmitted via the Foundation Fieldbus interface board.

FF ANALOG IN1

The setpoint E1 is transmitted via the Foundation Fieldbus interface board,
analogue input 1.

FF ANALOG IN2

The setpoint E1 is transmitted via the Foundation Fieldbus interface board,
analogue input 2.

Actuator controls
AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus

Manual

VIEW

SETPOINT E1

FOUNDATION FIELDBUS

C:ESC

Содержание Aumatic AC 01.1

































































































Результаты поиска

Содержание Aumatic AC 01.1

Отзывы:

AUMA Aumatic AC 01.1, Руководство пользователя, Страница: 54 / 96

Результаты поиска

Содержание Aumatic AC 01.1

Отзывы: