AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 39

Страница: 39 / 96

FAIL OPEN

The actuator runs to end position OPEN

FAIL TO PRESET

The actuator runs to a predetermined position.

Preset position definition

If the

FAIL TO PRESET

failure action (

FAILURE POSITION

parameter)

is set, the actuator runs to the preset position stated here.

Via the menu to parameter:

MAIN MENU (M0)

SETTINGS (M1)

FAILURE BEHAVIOUR (M15)

PRESET POSITION (M1513)

Standard value:

0.0 %

Setting range:

from

0.0 %

100.0 %

(from OPEN to CLOSED)

Failure delay time setting

Determines the time elapsed between the recognition of a cable break and
the initiation of the failure action.

Via the menu to parameter:

MAIN MENU (M0)

SETTINGS (M1)

FAILURE BEHAVIOUR (M15)

DELAY TIME (M1511)

Default value:

3.0

Setting range:

0.0

1200.0

seconds (20 minutes)

Actuator controls

Manual

AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus

EDIT

M1513

PRESET POSITION

0.0 %

:EDIT

↵

:OK

C:ESC

EDIT

M1511

DELAY TIME

3.0 s

:EDIT

↵

:OK

C:ESC

Содержание Aumatic AC 01.1

































































































Результаты поиска

Содержание Aumatic AC 01.1

Отзывы:

AUMA Aumatic AC 01.1, Руководство пользователя, Страница: 39 / 96

Результаты поиска

Содержание Aumatic AC 01.1

Отзывы: