manualshive.com logo in svg

AUMA Aumatic AC 01.1, Руководство пользователя, Страница: 28 / 96

Поделиться
Скачать
AUMA Aumatic AC 01.1 Скачать руководство пользователя страница 28

5.3.2 Source of the torque signal E6: view

This value is set in the factory and can only be changed by the AUMA ser-
vice.

Æ

Via the menu to parameter:

MAIN MENU (M0)

CONFIGURATION (M4)

SETUP (M41)

TORQUE E6 (M4103)

Default value:

depending on actuator

È

Description of the parameter settings:

NONE

There is no electronic torque monitoring available.

LOGIC ANALOG IN1

The torque signal is transmitted from an external sensor via the logic board
to the analogue input 1.

MWG

The torque signal is generated using the MWG installed in the actuator.

5.3.3 Feedback signals (configuration) via analogue output 1: view

Configuration of analogue output 1 (of the I/O).
Designation in the wiring diagram: ANOUT1.
This value is set in the factory and can only be changed by the AUMA ser-
vice.

Æ

Via the menu to parameter:

MAIN MENU (M0)

CONFIGURATION (M4)

SETUP (M41)

I/O1 ANALOG OUT1 (M410A)

Default value:

POSITION E2

È

Description of the parameter settings:

NOT USED

Analogue output 1 not used.

FEEDBACK E2:

Position feedback (analogue output 1 assigned to actual position signal).

If the actuator is equipped with a position transmitter (potentiometer, RWG
or MWG), an analogue position feedback (galvanically isolated) is available
as a 0/4 – 20 mA signal at the electrical connection (see wiring diagram). An
adjustment to the end positions or the defined travel is not required. An
automatic adjustment is done via the end positions (LSC (WSR) and LSO
(WOEL)).

28

Actuator controls
AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus

Manual

VIEW

I/O1 ANALOG OUT1

POSITION E2

C:ESC

VIEW

TORQUE E6

MWG

C:ESC

Содержание Aumatic AC 01.1

































































































Отзывы:

Нет отзывов