manualshive.com logo in svg

Atop EH9711 Series, Руководство пользователя

Поделиться
Скачать
Atop EH9711 Series Скачать руководство пользователя страница 140

Industrial Managed 
Ethernet Switch – EH9711 

User Manual 

 

 

Page 

140

 of 

223

 

 

GVRP  can  be used  to keep  VLAN  configurations  on trunk  interfaces  organized  across  the  network  on  large  networks  that 
consist of dozens or even  hundreds of VLAN  segments.  There are three benefits  for administrators  that enable GVRP on a 
network: 
 

 

It enables switches to automatically delete unused VLANs so that only the VLANs that are in use are transported 
across 802.1Q trunk links. 

 

It enables admins to configure a new VLAN on one switch and then have it propagate the configuration across all 
network switches participating in the GVRP process. 

 

GVRP can eliminate some unnecessary broadcast traffic on the network, reducing bandwidth overhead used for 
network management. 

GVRP works as follows. When two or more switches are connected via 802.1Q trunk ports with GVRP enabled in a network, 
these  switches  will  begin  to  communicate  statically  or  dynamically  through  VLAN  information.  Switches  with  statically 
configured VLANs will advertise them to connected switches  using GVRP data units. Those units are specifically  designed 
management  packets used to share VLAN  information.  If a switch  learns of a new  VLAN  from its neighbor, this VLAN is 
added to the list of VLAN tags that can be transported across the link The VLAN that learned the new information can then 
pass along  its own  statically  configured  VLANs,  in addition to ones  learned from  its neighbor.  For loop avoidance, switch 
cannot send dynamically learned VLAN information out the same interface that it was learned on.  
All the dynamically learned VLAN information

 

is stored in switch memory. So, if power is lost or the switch is rebooted, the 

dynamically  learned VLAN information is lost, and the VLANs  are pruned from the trunk interface. But, once the switches 
begin communication again, they will relearn the shared VLAN information to bring the network and all VLANs back into a 
fully informed state. 
 

2.17.1

 

Global config 

This GVRP

Global config webpage shown in Figure 2.115 allows the user to configure the global GVRP configuration 

settings that are commonly applied to all GVRP enabled ports.  

 

Figure 2.115 Webpage to Configure GVRP Globally 

 

Table 2.103 Descriptions of GVRP Globally Configuration  

Label 

Description

 

Factory 
Default

 

Join-time 

Join-time is a value in the range of 1-20cs, i.e. in units of one hundredth of a 
second. The default value is 20cs

 

20

 

Leave-time 

Leave-time is a value in the range of 60-300cs, i.e. in units of one hundredth of a 
second. The default is 60cs. 

60 

LeaveAll-time 

LeaveAll-time is a value in the range of 1000-5000cs, i.e. in units of one 
hundredth of a second. The default is 1000cs. 

1000 

Max VLANs 

When GVRP is enabled, a maximum number of VLANs supported by GVRP is 
specified. By default, this number is 20. This number can only be changed when 
GVRP is turned off. 

20 

Содержание EH9711 Series
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды