background image

Line

Function

Setting range or display

Setting increment 

Basic setting

Test of inputs/outputs

7700

I

Relay test

No test

This test consists of commanding the regulator relays one by one and checking the outputs. This permits a check that 

the relays are operating and that the wiring is correct (for this, check that each appliance is operating on the installation).

(0) No test

(1) Everything is STOPPED 

(2) Relay output QX23 module 1:

 Pool circulator , 

(3) Relay output QX21 

module 1:

 not used, 

(4) Relay output QX22 module 1:

 not used, 

(5) Relay output QX1:

 opening valve for circuit 1 

mixer, 

(6) Relay output QX2:

 Closure of circuit 1 mixing valve, 

(7) Relay output QX3:

 Circuit 1 heating Circulator , 

(8) Relay output QX4:

 SHW Circulator , 

(9) Relay output QX5:

 not used, 

(10) Relay output QX6:

 Starting of burner, 

(11) Relay output QX23 module 2:

 Circuit 2 heating Circulator  or pool Circulator , 

(12) Relay output QX21 module 

2:

 Opening valve for circuit 2 mixer, 

(13) Relay output QX22 module 2:

 Closure of circuit 2 mixing valve, 

(14) Relay 

output QX7: 

Not used.

The display shows the "key" symbol. By pressing the Info button, "error 368" is displayed.

Warning! During the test, the component tested is electrically powered.

7710

I

Test on output Ux

--, 0... 100%

1

--

7711

I

Voltage value Ux

0    10 Volt

0

7720

I

Digital outputs test

0 = No test               
1 = Everything is stopped
2 = Digital output DO1  
3 = Digital output DO2

No test

7721

I

Digital output  DO1

Cooling level,

 

Heating level

Heating 

operation

7722

I

Digital output  DO2

Stop, Start

Stop

7730

I

Outdoor temperature (B9)

-50... 50 °C

0

7820

I

Temperature sensor BX1

-28... 350 °C

0

7823

I

Temperature sensor BX4

-28... 350 °C

0

7824

I

Temperature sensor BX5

-28... 350 °C

0

7830

I

Temperature sensor BX21 module 1

-28... 350 °C

0

7831

I

Temperature sensor BX22 module 1

-28... 350 °C

0

7832

I

Temperature sensor BX21 module 2

-28... 350 °C

0

7833

I

Temperature sensor BX22 module 2

-28... 350 °C

0

7841

I

H1 contact  state

Open, Closed

Open

7846

I

H2 contact  state

Open, Closed

Open

7855

I

H3 contact  state

Open, Closed

Open

7914

I

Input Ex4

0, 230 V

0

7915

I

Input Ex5

0, 230 V

0

7916

I

Input Ex6

0, 230 V

0

State

8000

I

State of heating circuit 1

0

8001

I

State of heating circuit 2

0

8003

I

State of circuit SHW

0

8004

I

State of cooling circuit 1

0

8006

I

State of heat pump

0

8011

I

State of pool circuit 

0

8022

I

State of additional generator

0

8050

I

History 1

Date, time, state code 

8052

I

History 2

Date, time, state code

8054

I

History 3

Date, time, state code

Installation and operating manual

 "

1605 - EN

"

alfea hybrid duo heat pump oil low NOx CH

- 48 -

Содержание alfea excellia duo 11





































































Отзывы: